Yaskawa VS-626 MC5 - Manual (Page 284)

12.5 User Constants
- 15
12.5 User Constants
Factory settings are given for a 200 V class Inverter of 0.4 kW set to open loop vector control (A1-02 = 2).
Table
12.1 User Constants
No.
Name
(Display)
Factory
Setting Setting No.
Name
(Display)
Factory
Setting Setting
A1-00 Language selection for digital operator display
(Select Language) 1
1
b5--08 -- -- 4 0.00
A1-01 Constant access level
(Access Level)
2 b6-01 -- -- 4 0.0
A1-02 Control method selection
(Control Method) 2
1
b6-02 -- -- 4 0.0
A1-03 Initialize
(Init Parameters) 0 b6-03 -- -- 4 0.0
A1-04 Password 1
(Enter Password) 0 b6-04 -- -- 4 0.0
A1-05 Password 2
(Select Password)
0 b7-01 -- -- 4 0.0
A2-01
to
A2-32
User setting constant
(User Pram 1 to 32) b7-02 ---- 4 0.05
b1-01 Reference selection
(Reference Source)
1 C1-01 Acceleration time 1
(Accel Time 1)
10.0
b1-02 Operation method selection
(Run Source)
1 C1-02 Deceleration time 1
(Decel Time 1)
10.0
b1-03 Stopping method selection
(Stopping Method)
0 C1-03 Acceleration time 2
(Accel Time 2)
10.0
b1-04 Prohibition of reverse operation
(Reverse Oper)
0 C1-04 Deceleration time 2
(Decel Time 2)
10.0
b1-05 Operation selection for setting of E1-09 or less
(Zero-Speed Oper)
0 C1-05 Deceleration time 2
(Decel Time 2)
10.0
b1-06 Read sequence input twice
(Cntl Input Scans)
1 C1-06 Acceleration time 3
(Accel Time 3)
10.0
b1-07 Operation after switching to remote mode *2
(LOC/REM RUN Sel) 0 C1-07 Acceleration time 4
(Accel Time 4)
10.0
b1-08 Run command selection for PRG mode (RUN
CMD at PRG)
0 C1-08 Deceleration time 4
(Decel Time 4) 10.0
b2-01
Zero speed level (DC injection braking start
frequency)
(DCInj Start Rreq)
0.5 C1-09 Emergency stop time
(Fast Stop Time) 10.0
b2-02 DC injection braking current
(DCinj Current)
50 C1-10 Accel/decel time setting unit
(Acc/Dec Units)
1
b2-03 DC injection braking time at start
(DCInj Time @ Start)
0.00 C1-11 Accel/decel time switching frequency
(Acc/Dec SW Freq)
0.0
b2-04 DC injection braking time at stop
(DCInj Time @ Stop)
0.50 C2-01 S-curve characteristic time at acceleration start
(SCrv Acc @ Start)
0.20
b3-01 Speed search selection at start
(SpdSrch at Start) 0
3
C2-02 S-curve characteristic time at acceleration end
(SCrv Acc @ End)
0.20
b3-02 Speed search operating current
(SpdSrch Current) 100
3
C2-03 S-curve characteristic time at deceleration start
(SCrv Dec @ Srat) 0.20
b3-03 Speed search deceleration time
(SpdSrch Dec Time)
2.0 C2-04 S-curve characteristic time at deceleration end
(SCrv Dec @ End)
0.00
b4-01 Timer function ON-delay time
(Delay-ON Timer)
0.0 C3-01 Slip compensation gain
(Slip Comp Gain) 1.0
3
b4-02 Timer function OFF-delay time
(Delay-OFF Timer) 0.0 C3-02 Slip compensation primary delay time
(Slip Comp Time) 200
3
b5-01 -- -- 4 0 C3-03 Slip compensation limit
(Slip Comp Limit) 200
b5-02 -- -- 4 1.00 C3-04 Slip compensation during regeneration
(Slip Comp Regen)
0V
b5-03 -- -- 4 1.0 C3-05 Flux calculation method
(Flux Select) 0
b5-04 -- -- 4 100.0 C3--06 Output voltage limited operation selection
(Output V Limit) 0
b5-05 -- -- 4 0.00 C4-01 Torque compensation gain
(Torq Comp Gain) 1.00
b5-06 -- -- 4 100.0 C4-02 Torque compensation time constant
(Torq Comp Time) 20
3
b5-07 -- -- 4 0.0 C4--03 Start torque compemsation (forward direction)
(F TorqCmp @ Start) 0.0
* 1. Not initialized. (Japanese standard specifications: A1-01 = 1, A1-02 = 2)
* 2. Not displayed for some models depending on software version No.
* 3. Factory setting depends on the control method (A1-02).
* 4. Constants that cannot be used. (Do not change the settings)
12