Yaskawa Z1000 AC Drive HVAC - Manual (Page 369)

Overcurrent ...................................................................... 203
Overcurrent Detection Gain ............................................. 178, 295
Overexcitation Deceleration Gain ............................................ 296
Overexcitation Operation Selection .......................................... 296
Overheat 1 (Heatsink Overheat) .............................................. 204
Overheat Alarm Level.................................................... 175, 294
Overheat Pre-Alarm Operation Selection ............................. 175, 294
Overload Protection ............................................................ 254
Overtorque Detection 1 ........................................................ 206
Overvoltage...................................................................... 206
Overvoltage 2 ................................................................... 207
Overvoltage Protection......................................................... 254
ov Suppression Function Selection........................................... 292
P
Parameter Access Level........................................................ 146
Parameter Range Setting Error................................................ 218
Parameter Selection Error ..................................................... 219
Parameter Settings .............................................................. 109
Parameters to Minimize Motor Hunting and Oscillation .................. 193
PASS ............................................................................. 216
Password ......................................................................... 146
Password Settings............................................................... 146
Peak Hold Current .............................................................. 313
Peak Hold Output Frequency ................................................. 313
Permanent Magnet Motor Control............................................ 116
PF ................................................................................. 207
Phase Order Selection .......................................................... 151
PI Accel/Decel Time ........................................................... 158
PID Feedback Loss ....................................................... 202, 213
PI Feedback...................................................................... 314
PI Feedback Function Selection .............................................. 160
PI Feedback High Detection Level ........................................... 160
PI Feedback High Detection Time ........................................... 160
PI Feedback Loss Detection Selection ....................................... 156
PI Feedback Low Detection Level ........................................... 157
PI Feedback Low Detection Time ............................................ 157
PI Feedback Offset ............................................................. 160
PI Function Setting ............................................................. 155
PI Input (feedback) ............................................................. 314
PI Input Limit ................................................................... 160
PI Maximum Boost Time...................................................... 159
PI Monitors ...................................................................... 187
PI Offset Adjustment ........................................................... 156
PI Output......................................................................... 314
PI Output Fault.................................................................. 233
PI Output Gain Setting ......................................................... 156
PI Output Level Selection ..................................................... 156
PI Output Limit ................................................................. 156
PI Output Lower Limit......................................................... 160
PI Output Monitor Calculation Method...................................... 161
PI Output Reverse Selection .................................................. 156
PI Primary Delay Time Constant ............................................. 156
PI Setpoint ....................................................................... 314
PI Setpoint Boost Setting ...................................................... 159
PI Setpoint Display Digits ..................................................... 161
PI Setpoint Monitor Unit Selection........................................... 162
PI Setpoint Scaling ............................................................. 158
PI Setpoint Selection ........................................................... 158
PI Setpoint User Display....................................................... 161
PI Setpoint Value ............................................................... 158
PI Sleep Delay Time ........................................................... 158
PI Sleep Function Start Level ................................................. 157
PI Sleep Input Source .......................................................... 159
PI Snooze Deactivation Level................................................. 159
PI Snooze Delay Time ......................................................... 159
PI Snooze Feedback Level .................................................... 159
PI Snooze Level................................................................. 159
PI Square Root Gain............................................................ 160
PI Unit Selection ................................................................ 161
PM Motor Auto-Tuning Mode Selection .................................... 141
PM Motor Base Frequency .................................................... 142
PM Motor d-Axis Inductance ................................................. 142
PM Motor Induced Voltage Constant ........................................ 143
PM Motor Parameter Settings................................................. 137
PM Motor q-Axis Inductance ................................................. 143
PM Motor Rated Current ...................................................... 142
PM Motor Rated Power........................................................ 142
PM Motor Rated Voltage ...................................................... 142
PM Motor Stator Resistance .................................................. 142
PM Motor Type ................................................................. 142
Powering Up the Drive......................................................... 117
Power Ratings (Three-Phase 600 V Class).................................. 250
Preparing the Ends of Shielded Cables ..................................... 0
Present Value Access........................................................... 328
Previous Fault ................................................................... 310
Programming Errors............................................................ 218
Programming Mode ...................................................... 106, 109
Proportional Gain Setting (P) ................................................. 155
Protective Cover ..................................................................40
Protective Covers, Reattaching .................................................77
Protective Covers, Removing .............................................. 76, 77
Protective cover to prevent miswiring .........................................33
Pull-In Current .................................................................. 297
Pull-In Current Compensation Time Constant.............................. 297
Pull-In Current Level for PM Motor Tuning................................ 143
Pump (Secondary) Application ............................................... 120
Pump with PI Control Application .......................................... 120
R
R-....................................................................................87
R+...................................................................................87
Radiated and Radio Frequency Noise........................................ 247
Rated Current Depending on Carrier Frequency ........................... 256
Rated Current Setting Alarm .................................................. 222
Rated Slip Error ................................................................. 223
rdEr ............................................................................... 225
READ ............................................................................ 184
rEAd .............................................................................. 225
Reading BACnet Drive Parameters .......................................... 333
Reading Parameter Settings ................................................... 225
Real Time Clock Setting................................................. 108, 185
Reattaching the Front Cover ....................................................78
Reattaching the HOA Keypad ..................................................78
Reattaching the Protective Cover...............................................79
Reattaching the Terminal Cover ........................................... 76, 77
Removing the Front Cover ......................................................78
Removing the HOA Keypad ....................................................78
Removing the Protective Cover.................................................79
Removing the Terminal Cover............................................. 76, 77
Index
YASKAWA ELECTRIC TOEP YAIZ1U 03A YASKAWA AC Drive – Z1000 User Manual 369