Yaskawa Z1000 AC Drive HVAC - Manual (Page 370)

RESET Key...................................................................... 101
Resistance Tuning Error ....................................................... 222
Response Messages from Drive to Master .................................. 327
Return Fan with PI Control Application..................................... 119
Reverse Operation Selection .................................................. 151
Reverse Operation Selection 2 by PI Output................................ 162
rF .................................................................................. 208
rH ................................................................................. 208
Rotational Auto-Tuning for V/f Control..................................... 136
rr................................................................................... 208
RS-485 Interface ................................................................ 321
RTS Control Selection ................................................... 172, 323
Rubber Bushing ...................................................................28
Run Command/Frequency Reference Source Selection Error............ 219
Run Command at Power Up................................................... 151
Run Command Method Selection ...................................... 173, 324
Run Command Selection ...................................................... 229
RUN Command Selection for AUTO mode ................................ 264
Run Command Selection for AUTO Mode ................................. 123
Run Command Source Selection ............................................. 314
S
S- ....................................................................................87
S: Special Parameters .......................................................... 301
S+ ...................................................................................87
S1 ...................................................................................86
S1: Dynamic Noise Control Function........................................ 301
S2 ...................................................................................86
S2: Sequence Timers ........................................................... 301
S3 ...................................................................................86
S4 ...................................................................................86
S5 ...................................................................................86
S6 ...................................................................................86
S7 ...................................................................................86
SC .............................................................................86, 208
S-Curve Characteristics .................................................. 163, 193
SE ................................................................................. 216
Secondary PI Disable Mode................................................... 304
Secondary PI Display Digits .................................................. 303
Secondary PI Enable Selection ............................................... 303
Secondary PI Feedback Detection Selection ................................ 304
Secondary PI High Feedback Detection Time .............................. 304
Secondary PI High Feedback Level .......................................... 304
Secondary PI Integral Limit Setting.......................................... 304
Secondary PI Integral Time Setting .......................................... 304
Secondary PI Low Feedback Detection Level .............................. 304
Secondary PI Low Feedback Detection Time .............................. 304
Secondary PI Output Level Selection ........................................ 304
Secondary PI Output Lower Limit ........................................... 304
Secondary PI Output Upper Limit............................................ 304
Secondary PI Proportional Gain Setting ..................................... 304
Secondary PI Setpoint Value.................................................. 304
Secondary PI Unit Selection .................................................. 303
Secondary PI User Display .............................................. 303, 305
Second Line Monitor Selection ............................................... 181
Selecting the Type of Auto-Tuning .......................................... 138
Selection of Parameter Write during Uv..................................... 299
Self-Diagnostics................................................................. 335
Sequence Timer 1 Day Selection ............................................. 301
Sequence Timer 1 Reference Source......................................... 301
Sequence Timer 1 Selection................................................... 301
Sequence Timer 1 Start Time ................................................. 301
Sequence Timer 1 Stop Time ................................................. 301
Sequence Timer 2 Day Selection ............................................. 302
Sequence Timer 2 Reference Source......................................... 302
Sequence Timer 2 Selection................................................... 302
Sequence Timer 2 Start Time ................................................. 302
Sequence Timer 2 Stop Time ................................................. 302
Sequence Timer 3 Day Selection ............................................. 302
Sequence Timer 3 Reference Source......................................... 302
Sequence Timer 3 Selection................................................... 302
Sequence Timer 3 Start Time ................................................. 302
Sequence Timer 3 Stop Time ................................................. 302
Sequence Timer 4 Day Selection ............................................. 303
Sequence Timer 4 Reference Source......................................... 303
Sequence Timer 4 Selection................................................... 303
Sequence Timer 4 Start Time ................................................. 302
Sequence Timer 4 Stop Time ................................................. 303
Sequence Timer Error .......................................................... 221
SEr ................................................................................ 208
Serial Comms Cable Connection Terminal ................................. 320
Serial Communication Terminals...............................................87
Serial Communication Transmission Error ................................. 211
Set Time.............................................................. 108, 185, 300
Setup Group ..................................................................... 111
Setup Group Parameters ....................................................... 112
Setup Mode ...................................................................... 109
Shielded Twisted-Pair Cables ................................................ 0
Side-by-Side Installation.........................................................39
Side-by-Side Setup ...............................................................39
Simple Motor Setup Using V/f Control...................................... 115
Simplified Setup Using the Setup Group .................................... 109
Sinking/Sourcing Mode for Digital Inputs ....................................92
SN...................................................................................86
Soft Charge Bypass Relay Maintenance..................................... 313
Soft Charge Bypass Relay Maintenance Time.............................. 214
Soft CLA Selection ............................................................. 295
Soft Starter Speed Reference at Previous Fault............................. 311
Software Current Limit Selection ............................................ 178
Software No. (Flash) ........................................................... 310
Software No. (ROM) ........................................................... 310
Software version ..................................................................25
Space Between Drives (Side-by-Side Mounting) ............................39
Speed Agreement Detection Level ........................................... 293
Speed Agreement Detection Level (+/-)..................................... 293
Speed Agreement Detection Width .......................................... 293
Speed Agreement Detection Width (+/-) .................................... 293
Speed Control Range ........................................................... 253
Speed Feedback Detection Control Gain .................................... 297
Speed Response ................................................................. 253
Speed Search Deactivation Current .......................................... 153
Speed Search Deceleration Time ............................................. 153
Speed Search Delay Time ..................................................... 153
Speed Search Detection Compensation Gain ............................... 154
Speed Search Method Selection .............................................. 154
Speed Search Restart Current Level.......................................... 154
Speed Search Restart Detection Time........................................ 154
Speed Search Selection at Start ............................................... 153
Speed Search Wait Time....................................................... 155
Stall Prevention ................................................................. 193
Index
370 YASKAWA ELECTRIC TOEP YAIZ1U 03A YASKAWA AC Drive – Z1000 User Manual