Teledyne 6200T - Sulfides Analyzer - Manual (Page 15)

6200T Total Sulfur Analyzer Table of Contents
Teledyne Analytical Instruments xv
LIST OF FIGURES
Figure 1-1: 6200T Basic Configuration........................................................................................................... 28
Figure 1-2: 6200T with IZS/Permeation Tube Option .................................................................................... 29
Figure 1-3: 6200T with M702 Calibrator Option ............................................................................................. 30
Figure 1-4: M501TS Converter Layout ........................................................................................................... 32
Figure 3-1: Front Panel Layout ....................................................................................................................... 41
Figure 3-2: Display Screen and Touch Control .............................................................................................. 41
Figure 3-3: Display/Touch Control Screen Mapped to Menu Charts ............................................................ 43
Figure 3-4: Rear Panel Layout—Converter and Analyzer.............................................................................. 44
Figure 3-5A: Internal Layout, Basic (no Valve or Second Gas Options) .......................................................... 46
Figure 3-6: Analog In Connector .................................................................................................................... 49
Figure 3-7: Analog Output Connector ............................................................................................................ 50
Figure 3-8: Current Loop Option Installed on the Motherboard ..................................................................... 52
Figure 3-9: Status Output Connector ............................................................................................................. 53
Figure 3-10: Control Input Connector ............................................................................................................... 55
Figure 3-11: Concentration Alarm Relay .......................................................................................................... 56
Figure 3-12: Rear Panel Connector Pin-Outs for RS-232 Mode ...................................................................... 58
Figure 3-13: CPU Connector Pin-Outs for RS-232 Mode ................................................................................ 59
Figure 3-14: JP2 Pins 21-22 on RS-232-Multidrop PCA .................................................................................. 60
Figure 3-15: RS-232-Multidrop PCA Host/Analyzer Interconnect Diagram ..................................................... 61
Figure 3-16: Pneumatic Connections–Basic Configuration–Using Bottled Span Gas ..................................... 65
Figure 3-17: Pneumatic Connections–Basic Configuration–Using Gas Dilution Calibrator ............................. 66
Figure 3-18: 6200T Gas Flow, Basic Configuration ......................................................................................... 67
Figure 3-19: Pneumatic Layout with Zero/Span Valves Option ....................................................................... 68
Figure 3-20: Pneumatic Layout with IZS Options ............................................................................................. 69
Figure 3-21: Pneumatic Layout with O
2
Sensor ............................................................................................... 71
Figure 3-22: Pneumatic Layout with CO
2
Sensor ............................................................................................. 72
Figure 3-23: Warning Messages ...................................................................................................................... 77
Figure 3-24: Functional Check ......................................................................................................................... 80
Figure 3-25: Reporting Range Verification ....................................................................................................... 82
Figure 3-26: Dilution Ratio Setup ..................................................................................................................... 83
Figure 3-27: SO
2
Span Gas Setting ................................................................................................................. 84
Figure 3-28: Zero/Span Calibration Procedure ................................................................................................ 85
Figure 4-1: Front Panel Display ...................................................................................................................... 89
Figure 4-2: Viewing 6200T TEST Functions .................................................................................................. 92
Figure 4-3: Viewing and Clearing 6200T WARNING Messages .................................................................... 94
Figure 5-1: SETUP – Configuration Information ............................................................................................ 97
Figure 5-2: SETUP – Analog Output Connector ............................................................................................ 98
Figure 5-3: SETUP RNGE – Reporting Range Mode ..................................................................................100
Figure 5-4: SETUP RNGE – Single Range Mode ........................................................................................101
Figure 5-5: SETUP RNGE – Dual Range Mode ..........................................................................................102
Figure 5-6: SETUP RNGE – Auto Range Mode ..........................................................................................103
Figure 5-7: SETUP RNGE – Concentration Units Selection ........................................................................104
Figure 5-8: SETUP RNGE – Dilution Ratio ..................................................................................................105
Figure 5-9: SETUP – Enable Password Security .........................................................................................107
Figure 5-10: SETUP – Enter Calibration Mode Using Password ...................................................................108
Figure 5-11: SETUP – Clock ..........................................................................................................................109
Figure 5-12: SETUP – Clock Speed Variable ................................................................................................110
Figure 5-13: SETUP – COMM Menu ..............................................................................................................111
Figure 5-14: COMM – Machine ID ................................................................................................................112
Figure 5-15: SETUP – VARS Menu ...............................................................................................................114
Figure 5-16: DIAG Menu ................................................................................................................................116
Figure 5-17: DIAG – Signal I/O Menu ............................................................................................................117
Figure 5-18: DIAG – Analog Output Menu .....................................................................................................118
Figure 5-19: DIAG – Analog I/O Configuration Menu .....................................................................................121
Figure 5-20: DIAG – Analog Output Calibration Mode ...................................................................................122
Figure 5-21: DIAG – Analog Output Calibration Mode – Single Analog Channel ..........................................123