Teledyne 6200T - Sulfides Analyzer User Manual
Page 17
6200T Total Sulfur Analyzer
Table of Contents
Teledyne Analytical Instruments
xvii
Figure 9-15:
Activate O
2
Sensor Stability Function ........................................................................................207
Figure 9-16:
O
2
Zero/Span Calibration ...........................................................................................................208
Figure 9-17:
CO
2
Sensor Calibration Set Up ..................................................................................................209
Figure 9-18:
CO
2
Span Gas Concentration Setup .........................................................................................210
Figure 9-19:
Activate CO
2
Sensor Stability Function .....................................................................................211
Figure 9-20:
CO
2
Zero/Span Calibration ........................................................................................................212
Figure 10-1:
Dynamic Multipoint Span Calibration .........................................................................................220
Figure 11-1:
Sample Particulate Filter Assembly ...........................................................................................228
Figure 11-2:
Critical Flow Orifice Assembly ...................................................................................................231
Figure 11-3:
Simple Leak Check Fixture ........................................................................................................234
Figure 11-4:
Hydrocarbon Scrubber Leak Check Setup ................................................................................234
Figure 12-1:
Viewing and Clearing Warning Messages .................................................................................240
Figure 12-2:
Example of Signal I/O Function .................................................................................................244
Figure 12-3:
CPU Status Indicator .................................................................................................................245
Figure 12-4:
Location of Relay Board Power Configuration Jumper ..............................................................251
Figure 12-5:
Manual Activation of the UV Light Shutter .................................................................................257
Figure 12-6:
Sensor Module Wiring and Pneumatic Fittings ..........................................................................262
Figure 12-7:
Sensor Module Mounting Screws ..............................................................................................263
Figure 12-8:
Sample Chamber Mounting Bracket ..........................................................................................264
Figure 12-9:
Hex Screw Between Lens Housing and Sample Chamber .......................................................265
Figure 12-10:
UV Lens Housing / Filter Housing ..............................................................................................266
Figure 12-11:
PMT UV Filter Housing Disassembled ......................................................................................266
Figure 12-12:
Disassembling the Shutter Assembly ........................................................................................268
Figure 12-13:
Shutter Assembly .......................................................................................................................269
Figure 12-14.
UV Lamp Adjustment .................................................................................................................270
Figure 12-15:
Location of UV Reference Detector Potentiometer ...................................................................271
Figure 12-16:
PMT Assembly - Exploded View ................................................................................................273
Figure 12-17:
Pre-Amplifier Board (Preamp PCA) Layout ...............................................................................275
Figure 13-1:
UV Absorption ............................................................................................................................286
Figure 13-2:
UV Light Path .............................................................................................................................289
Figure 13-3:
Source UV Lamp Construction ..................................................................................................289
Figure 13-4:
Excitation Lamp UV Spectrum Before/After Filtration ................................................................291
Figure 13-5:
PMT Optical Filter Bandwidth ....................................................................................................292
Figure 13-6:
Effects of Focusing Source UV in Sample Chamber .................................................................293
Figure 13-7:
Oxygen Sensor - Principles of Operation ..................................................................................296
Figure 13-8:
CO
2
Sensor Principles of Operation ..........................................................................................297
Figure 13-9:
CO2 Sensor Option PCA Layout and Electronic Connections ..................................................298
Figure 13-10:
Gas Flow and Location of Critical Flow Orifice ..........................................................................299
Figure 13-11:
Flow Control Assembly & Critical Flow Orifice...........................................................................300
Figure 13-12:
6200T Hydrocarbon Scrubber (Kicker) ......................................................................................301
Figure 13-13:
6200T Electronic Block Diagram ...............................................................................................303
Figure 13-14:
CPU Board Annotated ...............................................................................................................305
Figure 13-15:
6200T Sensor Module ................................................................................................................306
Figure 13-16:
6200T Sample Chamber ............................................................................................................307
Figure 13-17:
PMT Housing Assembly .............................................................................................................308
Figure 13-18:
Basic PMT Design .....................................................................................................................309
Figure 13-19:
PMT Cooling System .................................................................................................................310
Figure 13-20:
PMT Preamp Block Diagram .....................................................................................................312
Figure 13-21:
Relay Board Status LED Locations ...........................................................................................314
Figure 13-22:
Power Distribution Block Diagram .............................................................................................318
Figure 13-23:
Front Panel and Display Interface Block Diagram .....................................................................319
Figure 13-24:
Basic Software Operation ..........................................................................................................320
Figure 13-25:
Calibration Slope and Offset ......................................................................................................321
Figure 14-1:
Triboelectric Charging ................................................................................................................325
Figure 14-2:
Basic anti-ESD Work Station .....................................................................................................328