IAI America REXT - Manual (Page 74)

Chap
ter 3 G
a
tew
ay R u
n
it
Part 1 Specification
3
T
3.7.3 Com
The eight input
input, six word
position table,
Note that comm
(1) Addres
The reque
[1] CC-L
*1
RY 2F
RY 3F
RY 4F
RY 5F
RY 6F
RY 7F
*1) Bit r
*2) If a
will b
[1] Devi
*1
Addre
Wor
+2
+3
+4
+5
+6
+7
*1 Eac
Devic
comp
*2 If a
will b
b15 Up
mmand Area
t words and eig
s in this fixed a
among others.
mands cannot
ss Configurat
est command a
Link
PLC
to 20
to 30
to 40
to 50
to 60
to 70
register addres
command erro
e set in respon
iceNet, Profibu
ess
rd By
2
3
4
5
+1
6 +1
7 +1
ch address is a
ceNet type. Wit
prising the uppe
command erro
e set in respon
pper byte b8
Request c
Data
Data
Data
Data
Cannot b
b15 U
a
ght output word
area are assign
be used in the
tion
area and respo
output
 Ga
ss
or occurs, the m
nse data 1.
us, EtherNet/IP
yte
+4/+5
+6/+7
+8/+9
10/+11
12/+13
13/+14
PLC o
a relative addre
th the Profibus
er word are ind
or occurs, the m
nse data 1.
b7 Lower byt
command
a 0
a 1
a 2
a 3
be used.
Upper byte b8
Request
Da
Da
Da
Da
Cannot
ds from the initi
ned as a comm
direct numeric
onse command
ateway
 Axis
most significant
RS485SIO
output  Gate
ess from the be
, EtherNet/IP a
dicated as b0 to
most significan
te b0 b15
b7 Lower by
command
ata 0
ata 1
ata 2
ata 3
be used.
ial address of t
mand area wher
cal specification
d area consist o
s input Axi
t bit (b15) of the
eway  Axis
eginning of the
and RS485 SIO
o b7.
t bit (b15) of th
Upper byte b8
Respons
Da
Data 1 *2
Da
Da
Cannot
yte b0 b15
the gateway un
re various com
n mode.
of six input wor
is output
 G
e response com
input Axis
gateway, and
O types, byte a
he response co
b7 Lower b
e command
ata 0
(error code)
ata 2
ata 3
t be used.
5 Upper byte b
Respon
D
Data 1 *
D
D
Cann
nit are fixed are
mmands can be
rds and six out
Gateway
 PL
mmand will tur
s output  Ga
word addresse
ddresses are u
ommand will tur
byte b0
8 b7 Lower
nse command
Data 0
*2 (error code)
Data 2
Data 3
ot be used.
eas. With both o
e used to read/w
put words, resp
C input
RX
RX
RX
RX
RX
RX
n ON and an e
ateway  PL
es are used by
used and b8 to
rn ON and an e
r byte b0
output and
write the
pectively.
*1
2F to 20
3F to 30
4F to 40
5F to 50
6F to 60
7F to 70
error code
LC input
the
b15
error code
Part 1 Specification
-74-