WattMaster WM-WCC3-TGD-01B - Manual (Page 184)

WCC3.EXE SCREEN DESCRIPTIONS
WCC III Technical Guide 3-70
Satellite # 1 TREND LOGGING # 1 of Type: CHANGE OF STATE
Records time & date of
Starting at: *:* on */*
state changes on: K1h S1-K1h Reset by: //// being ON
Roll after 48 readings
Off --- 0. 10:01 12/01
On --- 1. 10:04 12/01
Off --- 2. 00:00 00/00
On
--- 3. 10:55 12/09
Off --- 4. 00:00 00/00
SAT CHANGE OF STATE TREND LOG SCREEN
Make your selection by pressing the <space bar> once for each
choice until the desired mode has been selected, and then press
<Enter> . (When you select a trend logging mode that is different
than that currently being displayed, the screen will be rewritten
with the appropriate screen and data.)
Record time & date of state change on: ________
Specifi es the [binary] point address for which the change-of-states
are to be recorded.
Starting at: 00:00 on 00/00
Specifi es the time and date that the trend log recording should
begin. (The time is represented in 24-hour format.) The system
considers *’s in these positions to be “wild cards.” Therefore, if
you want the system to always log the changes-of-state peaks
independent of the time and date, enter “*:* on */*.”
Reset by _________ being _____.
Specifi es the [binary] point address that will be used to reset (or
clear) the record trend log data. The fi rst fi eld specifi es the point
address, and the second specifi es the state or condition that the point
address needs to be in to clear the data. Because this second fi eld
is a “choice” fi eld, the list of available choices will be displayed at
the bottom of the screen:
<OFF, ON>
_________ after 48 readings
Specifi es whether the data logging process will stop after 48
readings have been taken or will continue (roll over). Because this
is a “choice” fi eld, the list of available choices will be displayed at
the bottom of the screen:
<Stop, Roll>
Satellite #: _____
Specifi es the number of the satellite you are currently editing.
If you would like to edit a different satellite, simply position the
cursor to this fi eld by using the cursor positioning (arrow) keys,
enter the desired satellite number, and press
<Enter> .
Trend Log #: ____
This fi eld actually contains two separate fi elds. The fi rst fi eld
specifi es the point “type” (i.e., analog input, control output, analog
output, etc.) and displays the current type in textual form. Because
this is a “choice” fi eld, the list of available choices will be displayed
at the bottom of the screen:
<ANALOG INPUT, CONTROL OUTPUT, ANALOG OUTPUT,
TREND LOGGING, LOGIC SWITCH, BINARY OUTPUT>
Make your selection by pressing the <space bar> once for each
choice until the desired mode has been selected, and then press
<Enter> . (If you select a point type that is different than that
currently being displayed, the screen will be rewritten with the
appropriate screen and data.)
The second fi eld specifi es the point number to edit. For the Trend
Log Screen, this number can range from one to eight. If you would
like to edit a different point, simply position the cursor to this fi eld
by using the cursor positioning (arrow) keys, enter the desired
point number, and press
<Enter> .
of Type
Specifi es which of the four available trend logging modes (analog
peak, analog trend, change-of-state, and run time) you wish to use.
Because this is a “choice” fi eld, the list of available choices will be
displayed at the bottom of the screen:
<ANALOG TREND, ANALOG PEAK,
CHANGE OF STATE, RUN TIME>
SAT Change of State Trend Log Screen
Satellite Trend Log Summary Screen’s WCC III Logical Address is XXXTYc, where XXX = Satellite Address #, T = Trend Log,
Y = Point Number, c = Change of State