WattMaster WM-WCC3-TGD-01B - Manual (Page 527)

12. WCC III INSTALLATION
GUIDE
WCC III Technical Guide 12-31
8 7
SAT ADDRESS 2 1
4
8
A 3 WIRE ROOM SENSOR WILL NOT
REQUIRE A LOAD RESISTOR WHEN SET
FOR A 1 VOLT INPUT.
WattMaster Controls Inc.
BINARY
INPUTS
BINARY
INPUTS
L8
ON OFF
128
32
16 64
L4
L3
L2
L1
L6
L5
L7
L11
L12
ON OFF
L10
L9
ON OFF
L15
L16
L14
L13
C H
4
3
5
6
2
1
LOCAL SET
STATUS 2
STATUS 3
STATUS 1
HSS XMIT
LOCAL SET
LOCAL SET DISABLE
BATT ON/ OFF
PULSE INPUT
OPTION 1
TEST
OPTION 3
OPTION 2
ON OFF
STATUS
HSS REC
SAT XMIT
SAT REC
ANALOG INPUT
JUMPER SELECTION
A 2 WIRE ROOM SENSOR WILL REQUIRE
A 300 OHM LOAD RESISTOR WHEN SET
FOR A 1 VOLT INPUT.
A 4 TO 20 mA SENSOR WILL REQUIRE A
50 OHM LOAD RESISTOR WHEN SET FOR
A 1 VOLT INPUT, OR A 250 OHM LOAD
RESISTOR WHEN SET FOR A 5 VOLT INPUT.
CURRENT
INPUT
THERMISTOR
INPUT
0 - 1V
0 - 5V
0 - 10V
THERM
0 - 1V
0 - 5V
0 - 10V
THERM
0 TO 10V
INPUT
0 TO 5V
INPUT
0 TO 1V
INPUT
0 - 10V
0 - 1V 0 - 5V
0 - 10V
THERM
0 - 1V 0 - 5V
THERM
0 - 1V
0 - 5V 0 - 10V
THERM
PROGRAMMABLE CONTROLLER
SAT III
CH I
10 A 2 50 V A C ~
5A 30 V D C
SA
VD
E
G5
Q-1
A 4
OM
R O N
DC2
4 V CH IN A
C~ DC
SA
VD
E
N
WCC3 BINARY IN W/ TIME DELAY WATTMASTER CONTROLS, INC
YS102072 REV 2
24VAC 120VAC
TO OTHER
SAT III OR TO
WCC III - MCD
CONNECTION FROM A SAT III CONTROLLER TO WCC3 BINARY INPUT W/TIME DELAY BOARD USING THE "NEW" HSS CABLE CONNECTION METHOD,
BUT USING THE HSS CABLE AS A POWER ONLY CONNECTION TO THE WCC3 BINARY INPUT W/TIME DELAY BOARD AND IGNORING THE HSS
COMMUNCATIONS TO AND FROM THE SAT III CONTROLLER.
HSS CABLE - ORDER STANDARD LENGTHS OF 1 FOOT, 1.5 FOOT, 3 FEET, 25 FEET, 40 FEET, 80 FEET, 120 FEET MAX
DRY INPUT CONTACTS ONLY
CONTACT CLOSURE TO GROUND
ONLY. NO 24VAC INPUTS
24
V
A C
GN
D
TO OTHER
SAT III OR TO
WCC III - MCD
WIRE "T" TO "T"
"R" TO "R"
"SHD" TO "SHD"
BINARY INPUT BOARD GETS POWER ONLY FROM THIS HSS CABLE. COMMUNICATIONS ARE IGNORED
SEE FRONT PAGE FOR
DIP SWITCH SETTINGS
WARNING: OBSERVE POLARITY
BETWEEN THE SAT III AND THE
BINARY INPUT BOARD - GROUND
CONNECTIONS MUST BE THE SAME.
SAT III CONTROLLER
PIN #1
ST
R IP E
IS
PIN
#1
SAT III
HSS PORT
120VAC WIRING IS BY OTHERS
THE VA RATING FOR THE SAT III CONTROLLER IS 15VA.
THE VA RATING FOR THE WCC3 BINARY INPUT BOARD IS 5 VA.
UP TO TWO WCC3 BINARY INPUT W/TIME
DELAY BOARDS MAY BE WIRED TO THE
SAT III CONTROLLER USING THIS
METHOD. CONNECT THE FIRST WCC3
BINARY INPUT W/TIME DELAY BOARD
TO THE SAT III CONTROLLER COVER
MOUNTED L1 TO L8 DIP SWITCH BINARY
INPUTS, AND THE SECOND WCC3
BINARY INPUT W/TIME DELAY BOARD
TO THE SAT III CONTROLLERS COVER
MOUNTED L9 TO L16 DIP SWITCH
BINARY INPUTS.
REPLACE THE DIP SWITCH IN THE
SAT III CONTROLLERS COVER WITH
THE SUPPLIED RIBBON CABLE.
OBSERVE POLARITY OF PIN # 1
CONNECT PIN 1 TO PIN 1 AS SHOWN
Figure 12-26: The WCC III Binary Input with Time Delay board typical wiring diagram - Old wiring connection
method along with the with the HSS cable method to get power from the SAT III controller
WCC III Binary Input with Time Delay Board Old Wiring Method