GE Industrial Solutions DV-300 DC Drive Users Manual - Manual (Page 11)

DV-300 Adjustable Speed Drives
—————— TABLE OF CONTENTS —————— IX
lisT of fiGures
1 - safeTy PreCauTions - PreCauTions de seCuriTé ............................................ 1
2 - desCriPTion, ComPonenT idenTifiCaTion and sPeCifiCaTions ................... 1
Fig 2.1: Base diagram of a converter .........................................................................................................................................1
Fig. 2.5.1: Drive dimensions for 20 A ... 185 A sizes (form 1) .................................................................................................15
Fig. 2.5.2: Drive dimensions for 280 A ... 650 A sizes (form 2) ...............................................................................................16
Fig. 2.5.3: Drive dimensions for 770 A ... 1050 A sizes (form 3) .............................................................................................17
3 - insTallaTion Guidelines ....................................................................................... 1
Figure 3.3.1: max Angle of Inclination .......................................................................................................................................2
Figure 3.3.2: Mounting Clearance ............................................................................................................................................3
4 - WirinG ProCedures ............................................................................................... 1
Figure 4.1.1: Removing the Front Panel ....................................................................................................................................1
Figure 4.4.1: R-TPD32-GE regulation card ................................................................................................................................6
Figure 4.4.2: Disposition of terminals from 1 to 42 ....................................................................................................................9
Figure 4.5.1.1: RS485 serial interface .....................................................................................................................................12
Figure 4.6.2.1: Installing the option card .................................................................................................................................15
Figure 4.7.1.1: 6KDV300DES card ..........................................................................................................................................16
Figure 4.8.1:Control sequencing ..............................................................................................................................................18
Figure 4.8.2: Example for relay interface ................................................................................................................................19
Figure 4.8.3: Typical connections ...........................................................................................................................................20
Figure 4.8.4: Encoder and Tachometer Connections ...............................................................................................................21
Figure 4.8.5: Programmable Inputs/outputs (option 6KCV300TBO) with relay and contacts ...................................................21
Figure 4.8.6: Programmable Inputs/outputs with PLC ..............................................................................................................22
Figure 4.8.7: 6KCV300DES connection ....................................................................................................................................22
Figure 4.9.1.1: Position of the super fast fuses .......................................................................................................................23
Figure 4.11.1: Potentials of the regulator section ...................................................................................................................31
5 - ConverTer oPeraTion ............................................................................................ 1
Figure 5.1.2.1: Moving inside a menu ......................................................................................................................................2
Figure 5.3.6.1: Above: Actual spd; Below: Motor current. Speed P too low. ..........................................................................45
Figure 5.3.6.3: Above: Actual spd; Below: Motor current. Speed I too high. ..........................................................................45
Figure 5.3.6.2: Above: Actual spd; Below: Motor current. Speed P too high. ..........................................................................45
Figure 5.3.6.4: Above: Actual spd; Below: Motor current. Speed P and Speed I set correctly. ...............................................45
Figure 5.3.6.5: Above: Flux reference; Below: Flux current. The regulator behavior is not good. Jumps are due to field chan-
ging. ..................................................................................................................................................................................46
Figure 5.3.6.7: Above: Flux reference; Below: Flux current. The increment in the field current has no jump. Variation compa-
red to Fig. 4.5.7: Increase of Flux P from 2 to 10%. Flux I = 5%. ......................................................................................46
Figure 5.3.6.6: Above: Flux reference; Below: Flux current. The reduction of the field current depends on the field time con-
stant. The reg has no influence. ........................................................................................................................................46
Figure 5.3.6.8: Above: Flux; Below: Output voltage. After a speed change the field current (Flux) has some jumps. Voltage P
= 10%, Voltage I = 80%. .................................................................................................................................................48
Figure 5.3.6.10: Above: Flux; Below: Output voltage. After a short transient, the field current and armature voltage are con-
stant. Voltage P = 40%, Voltage I = 50%. ........................................................................................................................48
Figure 5.3.6.9: Above: Flux; Below: Output voltage. The gain is too low. The armature voltage increases. Voltage P = 3%,
Voltage I = 5%. .................................................................................................................................................................48
Figure 5.3.7.1: Curve convertion flux/current .........................................................................................................................49
Figure 5.3.7.2: Blocks diagrams of field current regulator ......................................................................................................50
Figure 5.3.7.3: Above: Actual spd; Below: Motor current jumps with the speed changes due to a high moment of inertia. The
function Speed-up is not active. ........................................................................................................................................51
Figure 5.3.7.4: Above: Actual spd; Below: Motor current. The same drive with Speed -up function active. ............................51
6 - funCTion desCriPTion ........................................................................................... 1