Brocade Mobility RFS Controller CLI Reference Guide (Supporting software release 5.5.0.0 and later) User Manual
Page 1216
1208
Brocade Mobility RFS Controller CLI Reference Guide
53-1003098-01
23
peer <1-2> {ip-address <IP>} {hostname|ipsec-secure|router-id|udp}
peer <1-2> {ipsec-secure} {gw [<IP>|<WORD>]}
router-id [<IP>|<WORD>|any] After specifying the peer hostname, optionally specify router ID settings:
•
router-id – Optional. Configures the peer’s router ID in one of the following formats:
•
<IP> – Peer router ID in the IP address (A.B.C.D) format
•
<WORD> – Peer router ID range (for example, 100-120)
•
any – Peer router ID is not specified. This allows incoming connection from any router ID.
udp
{ipsec-secure gw|
port <1-65535>
{ipsec-secure}}
After specifying the peer hostname, optionally specify UDP settings:
The UDP option configures the encapsulation mode for this tunnel.
•
UDP – Optional. Configures UDP encapsulation (default encapsulation is IP)
•
ipsec-secure gw – Optional. Enables auto IPSec
•
port <1-65535> {ipsec-secure} – Optional. Configures the peer’s UDP port running the L2TPv3
service from 1 - 65535. After specifying the peer UDP port, optionally configure
the IPSec settings.
peer <1-2>
Configures the tunnel’s peer ID from 1 - 2. At any time the tunnel is established with only one peer.
ip-address <IP>
Optional. Configures the peer’s IP address in the A.B.C.D format
hostname [<FQDN>|any]
After specifying the peer IP address, optionally specify the peer’s hostname:
Optional. Configures the peers’ hostname. The hostname options are:
•
<FQDN> – Specifies the hostname as FQDN or partial DN
•
any – Peer name is not specified. If the hostname is ‘any’ this tunnel is considered as responder
only and will allow incoming connection from any host.
ipsec-secure
{gw [<IP>|<WORD>]}
After specifying the peer IP address, optionally specify the IPSec settings:
•
ipsec-secure – Optional. Enables auto IPSec
•
gw – Optional. Configures IPSec gateway IP address or hostname
•
<IP> – Configures IPSec gateway’s IP address
•
<WORD> – Configures IPSec gateway’s hostname
router-id
[<A.B.C.D>|<WORD>|any]
After specifying the peer IP address, optionally specify the router ID using one of the following options:
•
router-id – Optional. Configures the peer’s router-id in one of the following formats:
•
<A.B.C.D> – Peer router ID in the IP address (A.B.C.D) format
•
<WORD> – Peer router ID range (for example, 100-120)
•
any – Peer router ID is not specified. This allows incoming connection from any router ID.
udp
{ipsec-secure gw|
port <1-65535>
{ipsec-secure}}
After specifying the peer IP address, optionally specify the peer’s UDP port settings:
The UDP option configures the encapsulation mode for this tunnel.
•
UDP – Optional. Configures UDP encapsulation (default encapsulation is IP)
•
ipsec-secure gw – Optional. Enables auto IPSec
•
port <1-65535> – Optional. Configures the peer’s UDP port running the L2TPv3 service from 1 -
65535. After specifying the peer UDP port, optionally configure the IPSec settings.
peer <1-2>
Configures the tunnel’s peer ID from 1 - 2. At any time the tunnel is established with only one peer.
ipsec-secure
{gw [<IP>|<WORD>]}
Optional. Enables auto IPSec for this peer
•
gw – Optional. Configures IPSec gateway IP address or hostname
•
<IP> – Configures IPSec gateway’s IP address
•
<WORD> – Configures IPSec gateway’s hostname