Brocade Mobility RFS Controller CLI Reference Guide (Supporting software release 5.5.0.0 and later) - Manual (Page 42)

24 Brocade Mobility RFS Controller CLI Reference Guide
53-1003098-01
2
clear rtls [aeroscout|ekahau] {<DEVICE-NAME> {on <DEVICE-OR-DOMAIN-NAME>}|
on <DEVICE-OR-DOMAIN-NAME>}
clear spanning-tree detected-protocols {on <DEVICE-NAME>}
clear spanning-tree detected-protocols {interface [<INTERFACE-NAME>|ge <1-5>|
me1|port-channel <1-3>|pppoe1|up1|vlan <1-4094>|wwan1]} {on <DEVICE-NAME>}
clear vrrp [error-stats|stats] {on <DEVICE-NAME>}
rtls Clears Real Time Location Service (RTLS) statistics
aeroscout Clears RTLS Aeroscout statistics
ekahau Clears RTLS Ekahau statistics
on <DEVICE-NAME> This keyword is common to the ‘aeroscout’ and ‘ekahau’ parameters.
•
on <DEVICE-NAME> – Optional. Clears Aeroscout or Ekahau RTLS statistics AP, wireless controller,
or service platform
on
<DEVICE-OR-DOMAIN-NAME> This keyword is common to the ‘aeroscout’ and ‘ekahau’ parameters.
•
on <DEVICE-OR-DOMAIN-NAME> – Optional. Clears Aeroscout or Ekahau RTLS statistics on a
specified AP, wireless controller, service platform, or RF Domain
spanning-tree Clears spanning tree entries on an interface, and restarts protocol migration
detected-protocols Restarts protocol migration
on <DEVICE-NAME> Optional. Clears spanning tree entries on a specified device
•
<DEVICE-NAME> – Specify the name of the AP, wireless controller, or service platform.
spanning-tree Clears spanning tree entries on an interface and restarts protocol migration
detected-protocols Restarts protocol migration
interface
[<INTERFACE-NAME>|
ge <1-5>|me1|
port-channel <1-3>|
pppoe1|up1|
vlan <1-4094>|
wwan1] Optional. Clears spanning tree entries on different interfaces
•
<INTERFACE-NAME> – Clears detected spanning tree entries on a specified interface. Specify
the interface name.
•
ge <1-5> – Clears detected spanning tree entries for the selected GigabitEthernet interface.
Select the GigabitEthernet interface index from 1 - 5.
•
me1 – Clears FastEthernet interface status
•
port-channel <1-3> – Clears detected spanning tree entries for the selected port channel
interface. Select the port channel index from 1 - 3.
•
pppoe1 – Clears detected spanning tree entries for Point-to-Point Protocol over Ethernet
(PPPoE) interface
•
up1 – Clears detected spanning tree entries for the WAN Ethernet interface
•
vlan <1-4094> – Clears detected spanning tree entries for the selected VLAN interface. Select
a Switch Virtual Interface (SVI) VLAN ID from 1- 4094.
•
wwan1 – Clears detected spanning tree entries for wireless WAN interface.
on <DEVICE-NAME> Optional. Clears spanning tree entries on a specified device
•
<DEVICE-NAME> – Specify the name of the AP, wireless controller, or service platform.
vrrp Clears a device’s Virtual Router Redundancy Protocol (VRRP) statistics
VRRP allows a pool of routers to be advertized as a single virtual router. This virtual router is
configured by hosts as their default gateway. VRRP elects a master router, from this pool, and
assigns it a virtual IP address. The master router routes and forwards packets to hosts on the same
subnet. When the master router fails, one of the backup routers is elected as the master and its IP
address is mapped to the virtual IP address.
error-stats Clears global error statistics