Brocade Mobility RFS Controller CLI Reference Guide (Supporting software release 5.5.0.0 and later) - Manual (Page 774)

Brocade Mobility RFS Controller CLI Reference Guide 761
53-1003098-01
7
load-balancing advanced-params max-preferred-band-load [2.4GHGz|5GHzd] <0-100>
load-balancing advanced-params [max-neighbors <0-16>|min-common-clients
<0-256>|
min-neighbor-rssi <-100-30>|min-probe-rssi <-100-30>]
load-balancing [balance-br-loads|balance-band-loads|balance-channel-loads
[2.4GHz|5GHz]]
load-balancing band-control-strategy
[distribute-by-ratio|prefer-2.4GHz|prefer-5GHz]
advanced-params Configures advanced load balancing parameters
max-preferred-band-load Configures the maximum load on the preferred band, beyond which the other band is equally preferred
[2.4GHz|5GHz] <0-100> Select one of the following options:
•
2.4GHz – Configures the maximum load on 2.4 GHz, when it is the preferred band
•
5GHz – Configures the maximum load on 5.0 GHz, when it is the preferred band
The following keyword is common to the 2.4 GHz and 5.0 GHz bands:
•
<0-100> – Configures the maximum load as a percentage from 0 - 100
advanced-params Configures advanced load balancing parameters
max-neighbors <0-6> Configures the maximum number of confirmed neighbors to balance
•
<0-6> – Specify a value from 0 - 6. Optionally configure a minimum of 0 neighbors and a maximum of
6 neighbors
min-common-clients
<0-256> Configures the minimum number of common clients that can be shared with the neighbor for load
balancing
•
<0-256> – Specify a value from 0 - 256. Optionally configure a minimum of 0 clients and a maximum
of 256 clients.
min-neighbor-rssi
<-100-30> Configures the minimum signal strength (Received Signal Strength Indicator - RSSI) of a neighbor
detected
•
<-100-30> – Sets the signal strength in dBm. Specify a value from -100 - 30 dBm.
min-probe-rssi
<-100-30> Configures the minimum received probe signal strength required to qualify the sender as a common client
•
<0-100> – Sets the signal strength in dBm. Specify a value from -100 - 30 dBm.
balance-br-loads Enables neighbor AP load balancing. This option distributes the access point’s radio load amongst other
controller managed access point radios. This option is enabled by default.
balance-band-loads Enables balancing of the total band load amongst neighbors. This option balances the access point’s radio
load by assigning a ratio to both the 2.4 GHz and 5.0 GHz bands. Balancing radio load by band ratio allows
an administrator to assign a greater weight to radio traffic on either the 2.4 GHz or 5.0 GHz band. This
option is enabled by default.
balance-channel-loads
[2.4GHz|5GHz] Enables the following:
•
2.4GHz – Channel load balancing on 2.4 GHz band
Balances the access point’s 2.4 GHz radio load across channels supported within the country of
deployment. This can prevent congestion on the 2.4 GHz radio if a channel is over utilized.
•
5GHz – Channel load balancing on 5.0 GHz band
Balances the access point’s 5.0 GHz radio load across channels supported within the country of
deployment. This can prevent congestion on the 5.0 GHz radio if a channel is over utilized.
band-control-strategy Configures a band control strategy
distribute-by-ratio Distributes clients to either band according to the band-ratio
prefer-2.4GHz Nudges all dual-band clients to 2.4 GHz band
prefer-5GHz Nudges all dual-band clients to 5.0 GHz band