Brocade Mobility RFS Controller CLI Reference Guide (Supporting software release 5.5.0.0 and later) - Manual (Page 910)

898 Brocade Mobility RFS Controller CLI Reference Guide
53-1003098-01
12
igp Identifies any private internal gateway (primarily used by CISCO for their IGRP) (number 9)
IGP enables exchange of information between hosts and routers within a managed network. The most
commonly used interior gateway protocol (IGP) protocols are: Routing Information Protocol (RIP) and Open
Shortest Path First (OSPF)
ospf Identifies the OSPF protocol (number 89)
OSPF is a link-state interior gateway protocol (IGP). OSPF routes IP packets within a single routing domain
(autonomous system), like an enterprise LAN. OSPF gathers link state information from neighbor routers and
constructs a network topology. The topology determines the routing table presented to the Internet Layer
which makes routing decisions based solely on the destination IP address found in IP packets.
vrrp Identifies the Virtual Router Redundancy Protocol (VRRP) protocol (number 112)
VRRP allows a pool of routers to be advertized as a single virtual router. This virtual router is configured by
hosts as their default gateway. VRRP elects a master router, from this pool, and assigns it a virtual IP
address. The master router routes and forwards packets to hosts on the same subnet. When the master
router fails, one of the backup routers is elected as the master and its IP address is mapped to the virtual IP
address.
<SOURCE-IP/MASK> Specifies the source IP address and mask (A.B.C.D/M) to match. Packets (EIGRP, GRE, IGMP, IGP, OSPF, or
VRRP) received from the specified sources are dropped.
<NETWORK-GROUP-ALIAS
-NAME> Applies a network-group alias to identify the source IP addresses. Packets (EIGRP, GRE, IGMP, IGP, OSPF, or
VRRP) received from the sources defined in the network-group alias are dropped.
•
<NETWORK-GROUP-ALIAS-NAME> – Specify the network-group alias name (should be existing and
configured).
any Specifies the source as any IP address. Packets (EIGRP, GRE, IGMP, IGP, OSPF, or VRRP) received from any
source are dropped.
from-vlan <VLAN-ID> Specifies a single VLAN or a range of VLANs as the match criteria. Packets (EIGRP, GRE, IGMP, IGP, OSPF, or
VRRP) received from the VLANs identified here are dropped.
•
<VLAN-ID> – Specify the VLAN ID. A range of VLANs is represented by the start and end VLAN IDs
separated by a hyphen (for example, 12-20).
Use this option with WLANs and port ACLs.
host
<SOURCE-HOST-IP> Identifies a specific host (as the source to match) by its IP address. Packets (EIGRP, GRE, IGMP, IGP, OSPF, or
VRRP) received from the specified host are dropped.
•
<SOURCE-HOST-IP> – Specify the source host’s exact IP address in the A.B.C.D format.
<DEST-IP/MASK> Specifies the destination IP address and mask (A.B.C.D/M) to match. Packets (EIGRP, GRE, IGMP, IGP, OSPF,
or VRRP) addressed to the specified destinations are dropped.
any Specifies the destination as any IP address. Packets (EIGRP, GRE, IGMP, IGP, OSPF, or VRRP) addressed to
any destination are dropped.
host <DEST-HOST-IP> Identifies a specific host (as the destination to match) by its IP address. Packets (EIGRP, GRE, IGMP, IGP,
OSPF, or VRRP) addresses to the specified host are dropped.
•
<SOURCE-HOST-IP> – Specify the destination host’s exact IP address in the A.B.C.D format.
<NETWORK-GROUP-ALIAS
-NAME> Applies a network-group alias to identify the destination IP addresses. Packets (EIGRP, GRE, IGMP, IGP, OSPF,
or VRRP) addressed to the destinations identified in the network-group alias are dropped.
•
<NETWORK-ALIAS-NAME> – Specify the network-group alias name (should be existing and configured).
After specifying the source and destination IP address(es), specify the action taken in case of a match.