Yaskawa Z1000U HVAC Matrix Bypass User Manual
Page 467
Removing the Front Cover .................................................... 100
Removing the Terminal Cover..................................................99
Replacement Parts .............................................................. 281
RESET Key...................................................................... 111
Resistance Tuning Error ....................................................... 262
Response Messages from Drive to Master ............................ 389, 441
Restart Enabled ................................................................. 173
Return Fan with PID Control Application................................... 123
Reverse Operation Selection .................................................. 134
Rotational Auto-Tuning for V/f Control..................................... 126
RS-485 Interface ................................................................ 385
Run Command/Frequency Reference Source Selection Error............ 260
Run Command Selection ................................................ 267, 268
RUN Command Selection for AUTO mode ................................ 311
Run Command Source Selection ............................................. 348
S
S: Special Parameters .......................................................... 198
S1: Dynamic Noise Control Function........................................ 337
S2: Sequence Timers ..................................................... 199, 337
SAFE ............................................................................. 257
Safety Circuit Fault ............................................................. 248
Safety Open Message Selection .............................................. 219
SCF ............................................................................... 248
S-Curve Characteristics .................................................. 153, 230
SE ................................................................................. 257
Selecting the Type of Auto-Tuning .......................................... 127
Sequence Timer 1............................................................... 199
Sequence Timer 1 Day Selection ............................................. 337
Sequence Timer 1 Reference Source......................................... 337
Sequence Timer 1 Selection................................................... 337
Sequence Timer 1 Start Time ................................................. 337
Sequence Timer 1 Stop Time ................................................. 337
Sequence Timer 2 Day Selection ............................................. 338
Sequence Timer 2 Reference Source......................................... 338
Sequence Timer 2 Selection................................................... 338
Sequence Timer 2 Start Time ................................................. 337
Sequence Timer 2 Stop Time ................................................. 338
Sequence Timer 3 Day Selection ............................................. 338
Sequence Timer 3 Reference Source......................................... 338
Sequence Timer 3 Selection................................................... 338
Sequence Timer 3 Start Time ................................................. 338
Sequence Timer 3 Stop Time ................................................. 338
Sequence Timer 4 Day Selection ............................................. 339
Sequence Timer 4 Reference Source......................................... 339
Sequence Timer 4 Selection................................................... 339
Sequence Timer 4 Start Time ................................................. 338
Sequence Timer 4 Stop Time ................................................. 338
Sequence Timer Error .......................................................... 261
Sequence Timers 1/2/3/4 Reference Source................................. 201
Sequence Timers 1/2/3/4 Selection........................................... 200
Sequence Timers 1 to 4 Day Selection....................................... 200
Sequence Timers 1 to 4 Start Time........................................... 200
Sequence Timers 1 to 4 Stop Time ........................................... 200
Sequence Timers 2 to 4 ........................................................ 199
SEr ................................................................................ 248
Serial Comm Alarm ............................................................ 251
Serial Communication Fault Detection Selection .......................... 436
Serial Communications Cable Connection Terminal (TB3) .. 364, 384, 433
Serial Communications Fault Time Select .................................. 436
Serial Communications Node Address Select .............................. 435
Serial Communications Protocol Select ..................................... 435
Serial Communications Receive to Transmit Wait Time.................. 436
Serial Communication Terminals...............................................98
Serial Communication Transmission Error ................................. 253
Setup Mode ...................................................................... 120
Shielded Twisted-Pair Cables ................................................. 103
Simplified Setup Using the Quick Setting Group .......................... 120
Slave Address ................................................................... 390
Smoke Purge in Bypass ........................................................ 251
Smoke Purge in Drive.......................................................... 251
Snubber Discharge Resistor Overheat ....................................... 248
Soft Charge Bypass Relay Maintenance..................................... 347
Soft Charge Bypass Relay Maintenance Time.............................. 256
Soft Starter Speed Reference at Previous Fault............................. 345
Software No. (Flash) ........................................................... 344
Software No. (ROM) ........................................................... 344
Software version ..................................................................59
SoH ............................................................................... 248
Speed Agree 1 ................................................................... 168
Speed Agree 2 ................................................................... 171
Speed Agree Detection Level ................................................. 186
Speed Agree Detection Level (+/-)........................................... 186
Speed Agree Detection Selection............................................. 187
Speed Agree Detection Width ................................................ 186
Speed Agree Detection Width (+/-) .......................................... 186
Speed Control Accuracy ....................................................... 303
Speed Control Range ........................................................... 303
Speed Search .................................................................... 133
Speed Search Deceleration Time ............................................. 137
Speed Search Delay Time ..................................................... 137
Speed Search Detection Compensation Gain ............................... 138
Speed Search Method Selection .............................................. 139
Speed Search Method Switching Level (Speed Estimation Type) ....... 138
Speed Search Restart Current Level.......................................... 139
Speed Search Restart Detection Time........................................ 139
Speed Search Selection at Start ............................................... 137
Speed Search Selection when Run Command is Given during Uv ...... 140
Speed Search Wait Time....................................................... 139
SrC ................................................................................ 248
Srr ................................................................................. 249
Stall Prevention ................................................................. 184
Stall Prevention Level during Acceleration ................................. 184
Stall Prevention Level during Run ........................................... 186
Stall Prevention Limit during Acceleration ................................. 185
Stall Prevention Selection during Acceleration............................. 331
Stall Prevention Selection during Deceleration............................. 185
Stall Prevention Selection during Run ....................................... 331
Standard .......................................................................... 303
Standard Connection Diagram ..................................................76
Starting Torque.................................................................. 303
Start Speed Search Select...................................................... 139
Station Address Setting Error ................................................. 251
Stationary Auto-Tuning........................................................ 127
Stationary Auto-Tuning for Line-to-Line Resistance ...................... 126
Status Display ................................................................... 122
Stopping Method Selection.................................................... 133
Storage Temperature .............................................................70
Supported Properties of Objects .............................................. 369
Surrounding Area .................................................................70
Index
YASKAWA SIEP YAIZ1D 01A Z1000U HVAC MATRIX Drive Bypass Technical Manual
467