Yaskawa iQpump1000 AC Drive Quick Start - Manual (Page 193)

R un
C omm an d
P re-C ha rge
D ua l speed – C om plete via tim er
“Pre-cha rge
Active”
M essage &
D igital Ou tpu t
(H 2-0x = A4)
Ou tpu t
F requen cy
P 4-03
Pre-cha rge T im e
P4-02 – Pre-cha rge F requen cy
P4-01 Pre-cha rge level = 0.0
P4-06 – Pre-cha rge F requen cy 2
P4-07
Pre-cha rge T im e 2
PID N OT
disab led
Figure 4.17 Pre-Charge Dual Speed Complete via Timer
R un
C omm an d
P re-C ha rge
C om plete via PID F eedba ck (N orm al Acting PID)
“Pre-cha rge
Active”
M essage &
D igital Ou tpu t
(H 2-0x = A4)
Ou tpu t
F requen cy
P4-03
Pre-cha rge T im e
P4-02 – Pre-cha rge F requen cy
P4-01 – Pre-cha rge Le vel
b5-01 PID Se lect = 1 (Enab led) AND b5-09 Ou tpu t Le vel Se l = 0 (N orm al C ha racter)
PID
F eedba ck
Figure 4.18 Pre-Charge Complete via Normal PID Feedback
n Setpoint Boost after Lag Pump De-Staging
When a lag pump is de-staged (turned off), there can be a sudden drop in pressure in the system due to the pump de-staging.
The Setpoint Boost function will dampen the shock load (pressure dip) to the system by temporarily raising the PI setpoint of
the drive controller during de-staging.
The function will raise the setpoint to the measured feedback value at the time of de-staging for the time set in P3-11. When
the P3-11 time expires, the setpoint will return to the Q1-01 value and the drive operates normally. The intention of the feature
is to get the drive to begin accelerating as soon as a pump is de-staged, thus limiting the shock to the system since the PI
controller would tell the drive to accelerate anyway in response the de-staged pump. It is not intended to regulate at the boosted
setpoint for a long period of time.
• The maximum PI setpoint is limited to the Q1-01 setpoint plus the P3-10 (Max Boost at De-Stage) setting.
• This feature cannot decrease the setpoint, therefore the function is disabled if b5-09 = 1 (inverse acting).
• If the iQpump controller calls for a lag pump to be staged during the P3-11 time, the staging will occur with the Setpoint
Boost function being immediately disabled.
• Setting either P3-10 or P3-11 to zero disables the Setpoint Boost function.
• The PI control loop is active during Setpoint Boost.
• The default setting for P3-10 is 0.0 PSI and P3-11 is 5.0 sec.
While the setpoint is being controlled by the Setpoint Boost after De-stage function, the drive will display the message "Setpoint
Boost Active (P3-11)."
Start Up Procedure
1.
Set all other parameters required for the application such as PI control loop, sleep, motor, and I/O parameters. Refer
to Vertical Turbine Controller (VTC) on page 188 for an example. However, this function can be used in conjunction
across a wide range of applications using a PI control process loop with multiple lag pumps that are staged and de-
staged
4.5 iQpump Presets and Functions
YASKAWA TOEP YAIP1W 01B YASKAWA AC Drive - iQpump1000 Quick Start Guide 193
4
Start-Up Programming & Operation