PLANET XGS3-24040 - Manual (Page 741)

Commands for Security Function Chapter 2 Commands for 802.1x
41-13
Default: No named MAC-IP access-list.
Usage Guide: After assigning this commands for the first time, only an empty name access-list is
created and no list item included.
Examples: Create an MAC-IP ACL named macip_acl.
Switch(config)# mac-ip-access-list extended macip_acl
Switch(Config-MacIp-Ext-Nacl-macip_acl)#
41.19 permit | deny (ip extended)
Command: [no] {deny | permit} icmp {{<sIpAddr> <sMask>} | any-source | {host-source
<sIpAddr>}} {{<dIpAddr> <dMask>} | any-destination | {host-destination <dIpAddr>}}
[<icmp-type> [<icmp-code>]] [precedence <prec>] [tos <tos>][time-range<time-range-name>]
[no] {deny | permit} igmp {{<sIpAddr> <sMask>} | any-source | {host-source <sIpAddr>}}
{{<dIpAddr> <dMask>} | any-destination | {host-destination <dIpAddr>}} [<igmp-type>]
[precedence <prec>] [tos <tos>][time-range<time-range-name>]
[no] {deny | permit} tcp {{ <sIpAddr> <sMask> } | any-source | {host-source <sIpAddr> }}
[s-port { <sPort> | range <sPortMin> <sPortMax> }] {{ <dIpAddr> <dMask> } | any-destination |
{host-destination <dIpAddr> }} [d-port { <dPort> | range <dPortMin> <dPortMax> }]
[ack+fin+psh+rst+urg+syn] [precedence <prec> ] [tos <tos> ][time-range <time-range-name> ]
[no] {deny | permit} udp {{ <sIpAddr> <sMask> } | any-source | {host-source <sIpAddr> }}
[s-port { <sPort> | range <sPortMin> <sPortMax> }] {{ <dIpAddr> <dMask> } | any-destination |
{host-destination <dIpAddr> }} [d-port { <dPort> | range <dPortMin> <dPortMax> }] [precedence
<prec> ] [tos <tos> ][time-range <time-range-name> ]
[no] {deny | permit} {eigrp | gre | igrp | ipinip | ip | ospf | < protocol-num >} {{<sIpAddr>
<sMask>} | any-source | {host-source <sIpAddr>}} {{<dIpAddr> <dMask>} | any-destination |
{host-destination <dIpAddr>}} [precedence <prec>] [tos <tos>][time-range<time-range-name>]
Functions: Create a name extended IP access rule to match specific IP protocol or all IP protocol.
Parameters: <sIpAddr> is the source IP address, the format is dotted decimal notation; <sMask > is the
reverse mask of source IP, the format is dotted decimal notation; <dIpAddr> is the destination IP address,
the format is dotted decimal notation; <dMask> is the reverse mask of destination IP, the format is dotted
decimal notation, attentive position o, ignored position 1; <igmp-type>, the type of igmp, 0-15;
<icmp-type>, the type of icmp, 0-255 ; <icmp-code>, protocol No. of icmp, 0-255; <prec>, IP priority,
0-7; <tos>, to value, 0-15; <sPort>, source port No., 0-65535; <sPortMin>, the down boundary of
source port; <sPortMax>, the up boundary of source port; <dPort>, destination port No. 0-65535;
<dPortMin>, the down boundary of destination port; <dPortMax>, the up boundary of destination port;
<time-range-name>, time range name.
Command Mode: Name extended IP access-list configuration mode
Default: No access-list configured.
Examples: Create the extended access-list, deny icmp packet to pass, and permit udp packet with
destination address 192. 168. 0. 1 and destination port 32 to pass.
Switch(config)# access-list ip extended udpFlow