Yaskawa G5HHP Drive - Manual (Page 363)

12.7 User Constants
12 - 15
Table 12.1 User Constants (Continued)
No.
Name
(Display)
Factory
Setting
Setting No.
Name
(Display)
Factory
Setting
Setting
E3-01
Motor 2 control method selection * 1
(Control Method)
2 F4-03
Channel 2 monitor selection
(AO Ch2 Select)
3
E4-01 Motor 2 max. output frequency *
1
(V/F2 Max Freq)
60.0 F4-04
Channel 2 gain
(AO Ch2 Gain)
0.50
E4-02
Motor 2 max. voltage * 1
(V/F2 Max Voltage)
400.0
* 2
F5-01
Channel 1 output selection
(DO-02 Ch1 Select)
0
E4-03 Motor 2 max. voltage frequency *
1
(V/F2 Base Freq)
60.0 F5-02
Channel 2 output selection
(DO-02 Ch2 Select)
1
E4-04 Motor 2 mid. output frequency 1 *
1
(V/F2 Mid Freq)
3.0 F6-01
Output mode selection
(DO-08 Selection)
0
E4-05 Motor 2 mid. output frequency voltage 1 *
1
(V/F2 Mid Voltage)
22.0
* 2
F7-01
Frequency multiple selection
(PO-36F Selection)
1
E4-06 Motor 2 min. output frequency
(V/F2 Min Freq)
0.5 F8-01 Transmission option (SI-F/G) * 1
(E-15 Det Sel)
1
E4-07 Motor 2 min. output frequency voltage *
1
(V/F2 Min Voltage)
4.0
* 2
F9-01
External fault input level from transmissin op-
tion (FF0 Selection) * 1
0
E5-01 Motor 2 rated current *
1
(Motor 2 rated FLA)
370.0
*
3
F9-02
External fault detection from transmission option
(EF0 Detection) *
1
0
E5-02
Motor 2 rated slip * 1
(Motor 2 Slip Freq)
1.30
* 3
F9-03
Action for external fault from transmission op-
tion (EF0 Fault Act) * 1
1
E5-03
Motor 2 no-load current * 1
(Motor 2 No-load I)
96.0
* 3
F9-04
Transmission option trace sampling time
(Trace Sample Time) * 1
0
E5-04 Motor 2 number of poles * 1
(Motor 2 # Poles)
4 poles H1-01 Multi-function input (terminal 11)
(Terminal 11 Sel)
24
E5-05
Motor 2 line-to-line resistance * 1
(Motor 2 term Ohms)
0.020
* 3
H1-02
Multi-function input (terminal 12)
(Terminal 12 Sel)
14
E5-06 Motor 2 leak inductance *
1
(Motor 2 Leak)
5.0
*
3
H1-03
Multi-function input (terminal 13)
(Terminal 13 Sel)
3 (0)
*
5
F1-01
PG constant
(PG Pulse/Rev)
600 H1-04
Multi-function input (terminal 14)
(Terminal 14 Sel)
4 (3)
*
5
F1-02
Operation selection at PG open circuit
(PG Fdbk Loss Sel)
1 H1-05
Multi-function input (terminal 15)
(Terminal 15 Sel)
6 (4)
* 5
F1-03
Operation selection at overspeed
(PG Overspeed Sel)
1 H1-06
Multi-function input (terminal 16)
(Terminal 16 Sel)
8 (6)
* 5
F1-04
Operation selection at deviation
(PG Deviation Sel)
3 H2-01
Multi-function input (terminal 53--57)
(Terminal 53--57 Sel)
0
F1-05
PG rotation
(PG Rotation Sel)
0 H2-02
Multi-function input (terminal 19)
(Terminal 19 Sel)
1
F1-06 PG division rate (PG pulse monitor)
(PG output Ratio)
1 H2-03 Multi-function input (terminal 20)
(Terminal 26 Sel)
2
F1-07
Integral value during accel/decel enable/disable
(PG Ramp PI/I Sel)
0 H3-01
Signal level selection (terminal 36)
(Term 36 Signal)
0
F1-08
Overspeed detection level
(PG Overspd Level)
115 H3-02
Gain (terminal 36)
(Terminal 36 Gain)
100.0
F1-09
Overspeed detection delay time
(PG Overspd Time)
0.0
*
4
H3-03
Bias (terminal 36)
(Terminal 36 Bias)
0.0
F1-10 Excessive speed deviation detection level
(PG Deviate level)
10 H3-04 Signal level selection (terminal 42)
(Term 42 Signal)
0
F1-11
Excessive speed deviation detection delay time
(PG Deviate Time)
0.5 H3-05
Multi-function analog input (terminal 42)
(Terminal 42 Sel)
0
F1-12
Number of PG gear teeth 1
(PG# Gear Teeth 1)
0 H3-06
Gain (terminal 42)
(Terminal 42 Gain)
100.0
F1-13
Number of PG gear teeth 2
(PG# Gear Teeth 2)
0 H3-07
Bias (terminal 42)
(Terminal 42 Bias)
0.0
F1-14 PG open-circuit detection time *
1
(PGO Time)
2.0 H3-08
Signal level selection (terminal 39)
(Term 39 Signal)
2
12