Yaskawa G5HHP Drive - Manual (Page 371)

Index
Index- 5
Pulse Monitor Card, settings: 7---5 7 - 58
PWM timer error: chapt9 9 - 5
Q
Quick-start: chapt4 4 - 6
setting user constants: chapt4 4 - 9
Quick-start: chapt1 1 - 5
R
rated current
V/f control: 6---3 6 - 21
V/f control with PG: 6---5 6 - 39
reference source: 6---1 6 - 4
reverse operation: 6---1 6 - 11
RH (dynamic brake resistor): chapt9 9 - 3
RR (dynamic brake transistor): chapt9 9 - 3
run: 6---1 6 - 9
command: 6---1 6 - 9
source: 6---1 6 - 9
S
S-curve characteristic function: 7---5 7 - 47
SC (short circuit): chapt9 9 - 2
sequence control, 3-wire: 6---1 6 - 14
sequential operation: chapt4 4 - 25, 4 - 26
settings
analog output bias (terminal 21), H4-03: 6---4 6 - 36;
6---5 6 - 44
analog output bias (terminal 23), H4-06: 6---4 6 - 36;
6---5 6 - 45
analog output gain (terminal 21), H4-02: 6---4 6 - 36;
6---5 6 - 44
analog output gain (terminal 23), H4-05: 6---4 6 - 36;
6---5 6 - 45
analog output level selection, H4-07: 6---4 6 - 36
analog output selection (terminal 21), H4-01: 6---4 6
- 36; 6---5 6 - 44
analog output selection (terminal 23), H4-04: 6---4 6
- 36; 6---5 6 - 45
shared RAM BCC check error: chapt9 9 - 5
shared RAM mutual diagnosis error: chapt9 9 - 5
shared RAM write error: chapt9 9 - 5
SI-B communications error: chapt9 9 - 7
SI-F/G communications error detected: chapt9 9 - 7
side-by-side connection: 2---4 2 - 10
slip compensation gain: 7---3 7 - 32; 7---5 7 - 48
speed control
flux vector control: 6---4 6 - 33
integral reset, V/f control with PG: 6---5 6 - 44
integral time
flux vector control: 6---4 6 - 33; 6---5 6 - 43
low-speed gain: 6---4 6 - 33; 6---5 6 - 43
mode select, V/f control with PG: 6---5 6 - 44
proportional gain
flux vector control: 6---4 6 - 33; 6---5 6 - 43
low-speed gain: 6---4 6 - 33; 6---5 6 - 43
responsiveness, flux vector control: 6---4 6 - 35
V/f control with PG: 6---5 6 - 43
speed control gain, flux vector control: 6---4 6 - 36
fine adjustments: 6---4 6 - 36
speed control integral reset: 7---5 7 - 62
speed control proportional gain: 7---5 7 - 70
speed feedback: 7---1 7 - 5
speed limit function: 7---3 7 - 21
speed search function: 7---5 7 - 40
speed torque control change: 7---5 7 - 69
stall prevention function settings: 7---5 7 - 81
Status Monitor: chapt4 4 - 14
stopping method: 6---1 6 - 12
coasting: 6---1 6 - 12
coasting with timer: 6---1 6 - 13
DC injection braking: 6---1 6 - 12
deceleration: 6---1 6 - 12
flux vector control: 6---4 6 - 29
storage location: 2---1 2 - 3
storage method: 2---1 2 - 3
SVE (zero servo fault): chapt9 9 - 4
switching, speed control and torque control: 7---3 7 -
26
timer: 7---3 7 - 26
T
temperature: 2---4 2 - 10
terminal position: chapt3 3 - 5
timer function: 7---5 7 - 41