Basler Electric BE1-700 - Manual (Page 443)

Table B-7. General Setting Commands
Type ASCII Command Function
HMI
Screen
SG Read all general settings. N/A
SG-BL=<time> Read/Set the backlight timer. 6.4
SG-CLK[=<date format(M/D)>,<time
format(12/24)>]
Read/Program time and date format. N/A
SG-COM<#>[=<baud>,A<addr>,P<pglen>,
R<reply ack>,X<XON ena>]
Read/Set serial communication protocol.
6.1.1,
6.1.3
C SG-CT<x>[=<CT ratio>] Read/Set Phase/Neutral CT ratio.
6.3.1 -
6.3.2
C SG-DI<x>[=<interval>]
Read/Set P(IA/IB/IC/var/watt), N and Q
demand interval.
N/A
SG-DSP[P/N] Read analog signal dsp filter type. N/A
SG-EMAIL[#[={email logic}]] Read/Enter email logic. N/A
SG-FREQ[=<freq(Hz)>] Read/Enter power system frequency. 6.3.8
SG-HOLD<x>[=<1/0 hold ena>] Read/Program output hold operation. N/A
SG-ID[=<relayID>,<stationID>]
Read/Set relay ID and station ID used in
reports.
N/A
SG-IN<x>[=<Recognition Time>,<Debounce
Time>]
Read/Set input recognition/debounce. N/A
SG-NOM[=<nom volts>,<nom amps>] Read/Set nominal voltage and current. 6.3.7
SG-OSC[=<# records saved>]
Read/Set the number of oscillographic
fault records saved.
N/A
SG-PHROT[=<phase rotation>] Read/Set phase rotation setting. 6.3.9
SG-SCREEN<x>[=<default screen number>] Read/Set default screen(s). N/A
SG-SGCON[=<time>] Read/Set SGC output time. N/A
SG-TARG[=<x/x/…x>,<rst TARG logic>]
Report/Enable Target list and Reset
Target logic.
N/A
SG-TRIGGER<x>[=<TRIPtrigger>,<Putrigger>,
<LOGICtrigger>]
Read/Set trigger logic. N/A
V
SG-VTP[=<VT ratio>,<connection>,
<27/59 mode>,<51/27R mode>] Read/Set VT ratio, connection, and 27/59
pickup mode. 6.3.3 -
6.3.4
V SG-VTX[=<VT_ratio>,<connection>] Read/Set Aux. VT ratio and connection.
6.3.5 -
6.3.6
Table B-8. Breaker Monitoring and Setting Commands
Type ASCII Command Function HMI Screen
C SB Read all breaker settings. N/A
C SB-DUTY[=<mode>,<DMAX>] Read/Set breaker contact duty. N/A
C SB-LOGIC[=<breaker close logic>] Read/Set breaker contact logic. N/A
Table B-9. Programmable Logic Setting Commands
Type ASCII Command Function
HMI
Screen
SL[:<name>] Obtain setting logic information. N/A
V SL-24[=<mode>,<BLK logic>] Read/Set logic for 24 function modules. N/A
V SL-25[=<mode>,<BLK logic>] Read/Set logic for 25 function modules. N/A
V SL-<x>27<p>[=<mode>,<BLK logic>] Read/Set logic for 27 function modules. N/A
V SL-47[=<mode>,<BLK logic>] Read/Set logic for 47 function modules. N/A
9376700990 Rev M BE1-700 Command Cross-Reference B-3