Lenze E94AxPExxxx - Manual (Page 652)

14 Diagnostics & fault analysis
14.7 Error messages of the operating system
652
Lenze · 9400 Servo PLC· Reference manual · DMS 4.0 EN · 11/2013 · TD05/06
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
0x00780003 7864323 Motor load I²xt > C00120 Fault -
0x00780002 7864322 Motor load I²xt > C00127 Warning C00606
0x007b0038 8060984 Motor parameter identification cancelled Fault -
0x007b0025 8060965 Motor temperature: Module selected in C01193 is not available Fault -
0x007b001e 8060958 Motor: actual current > C00620 Fault C00619
0x007b0020 8060960 Motor: actual speed > C00596 Fault C00607
0x007b000b 8060939 Motor: Calculated e.m.f. factor unrealistic Information -
0x007b000d 8060941 Motor: Calculated flux factor unrealistic Information -
0x007b0019 8060953 Motor: Calculated leakage inductance unrealistic Information -
0x007b0001 8060929 Motor: Calculated motor impedance unrealistic Information -
0x007b0002 8060930 Motor: Calculated mutual inductance unrealistic Information -
0x007b000a 8060938 Motor: Calculated mutual inductance unrealistic Information -
0x007b0009 8060937 Motor: Calculated rotor resistance unrealistic Information -
0x007b000c 8060940 Motor: Calculated rotor time constant unrealistic Information -
0x007b0006 8060934 Motor: Device current too low for rated magnetisation Information -
0x00770003 7798787 Motor: Overtemperature Fault C00583
0x007b0004 8060932 Motor: Phase resistance too high Information -
0x0077000f 7798799 Motor: PTC has triggered No response C00585
0x007b0007 8060935 Motor: rated current < rated magnetisation current Information -
0x00770002 7798786 Motor: temperature > C00121 Warning C00584
0x0077000c 7798796 Motor: thermal detector is defective Fault C00594
0x008c0017 9175063 MXI1: CAN module is missing or incompatible Fault C00615/2
0x008c0013 9175059 MXI1: Digital frequency module is missing or incompatible Fault C00615/2
0x008c0011 9175057 MXI1: Ethernet module is missing or incompatible Fault C00615/2
0x008c0015 9175061 MXI1: ICM module is missing or incompatible Fault C00615/2
0x00680004 6815748 MXI1: Module changed during operation Warning locked -
0x00680015 6815765 MXI1: Module has been changed Information or warning locked if
the hardware type has also
changed.
-
0x0068000a 6815754 MXI1: Module is defective or missing Fault -
0x008c000d 9175053 MXI1: Module is missing or incompatible Fault -
0x008c000f 9175055 MXI1: PROFIBUS module is missing or incompatible Fault C00615/2
0x00680010 6815760 MXI1: Wrong module System fault -
0x008c0018 9175064 MXI2: CAN module is missing or incompatible Fault C00615/3
0x008c0014 9175060 MXI2: Digital frequency module is missing or incompatible Fault C00615/3
0x008c0012 9175058 MXI2: Ethernet module is missing or incompatible Fault C00615/3
0x008c0016 9175062 MXI2: ICM module is missing or incompatible Fault C00615/3
0x00680005 6815749 MXI2: Module changed during operation Warning locked -
0x00680016 6815766 MXI2: Module has been changed Information or warning locked if
the hardware type has also
changed.
-
0x0068000b 6815755 MXI2: Module is defective or missing System fault -
0x008c000e 9175054 MXI2: Module is missing or incompatible Fault -
0x008c0010 9175056 MXI2: PROFIBUS module is missing or incompatible Fault C00615/3
0x00680011 6815761 MXI2: Wrong module System fault -
0x00b8000a 12058634 Negative direction of rotation limited Information C02716/1
0x00b80002 12058626 Negative limit switch has triggered Quick stop by trouble -
0x00b80008 12058632 Negative software limit switch overtravelled Quick stop by trouble C02716/2
0x006a0003 6946819 New applications loaded Information -
0x00910002 9502722 No heartbeat signal detected System fault -
0x0090000a 9437194 No parameters for module in MXI1 Fault C00615/2
0x0090000b 9437195 No parameters for module in MXI2 Fault C00615/3
0x007b0010 8060944 Overcurrent detected Fault -
hex dec Error message Response (Lenze setting) can be set in