Yaskawa L1000E AC Drive Technical Manual for CIMR-LE Models for Elevator Applications - Manual (Page 193)

5.7 H: Terminal Functions
YASKAWA ELECTRIC SIEP YAIL1E 01A YASKAWA AC Drive L1000E Technical Manual 193
P
a
ra
me
te
r De
ta
ils
5
5.7 H: Terminal Functions
H parameters are used to assign functions to the external terminals.
◆ H1: Multi-Function Digital Inputs
NOTICE: Always turn off the RUN command before changing the setting of parameters d1-18 (Speed Reference Selection Mode), b1-
01 (Speed Reference Selection), or H1- †† (Multi-Function Digital Inputs). If the RUN command is on when changing any of these
settings, the motor may unexpectedly start running, and could result in injury.
■ H1-03 to H1-08: Functions for Terminals S3 to S8
These parameters assign functions to the multi-function digital inputs. The various functions and their settings are listed
in
Table 5.9 .
Table 5.9 Multi-Function Digital Input Terminal Settings
Setting 3 to 5: Multi-Step Speed Reference 1 to 3
Switches multi-step speed frequency references d1-01 to d1-08 by digital inputs. Refer to Speed Selection Using Digital
Inputs (b1-01 = 0) on page 121 for details.
Setting 6: Jog reference selection
When the speed reference is not assigned to the input terminals (b1-01 ≠ 1), then the Jog frequency will be activated every
time an input terminal set for the Jog frequency reference closes. Note that the speed reference priority selection in d1-18
may disable the Jog frequency.
Table 5.10 Speed Reference Priority and Jog Frequency
No.
<1> With the speed reference priority d1-18 is set to 0 or 3, the default settings for parameters H1-03 to H1-07 governing input terminals S3 to S7
are: 24, 14, 3, 4, and 5 respectively. When d1-18 is set to 1 or 2, the default settings for H1-03 to H1-07 become 50, 54, 51, 53, and F
respectively.
Parameter Name
Setting
Range
Default
H1-03 Terminal S3 Function Selection 3 to 79
Determined by d1-18 <1>
H1-04 Terminal S4 Function Selection 3 to 79
H1-05 Terminal S5 Function Selection 3 to 79
H1-06 Terminal S6 Function Selection 3 to 79
H1-07 Terminal S7 Function Selection 3 to 79
H1-08 Terminal S8 Function Selection 3 to 79 F: Through Mode
Setting Function Page Setting Function Page
3 Multi-Step Speed Reference 1
193
20 to 2F External Fault 196
4 Multi-Step Speed Reference 2 50 Nominal Speed 196
5 Multi-Step Speed Reference 3 51 Intermediate Speed 196
6 Jog reference selection 193 52 Releveling Speed 196
7 Accel/decel Ramp Selection 1 194 53 Leveling Speed 197
8 Baseblock Command (N.O.)
194
54 Inspection Operation 197
9 Baseblock Command (N.C.) 55 Rescue Operation 197
F Not used (Through Mode) 194 56 Motor Contactor Feedback 197
14 Fault Reset 194 57 High Speed Limit Up 197
15 Fast Stop (N.O.) 194 58 High Speed Limit Down 197
16 Motor 2 selection 195 5A Motor Contactor Feedback 2 197
17 Fast Stop (N.C.) 194 5B Brake Feedback 2 197
18 Timer Function Input 195 5C Stop Distance Correction 197
1A Accel/decel Ramp Selection 2 195
67 Communications Test Mode 197
79 Brake Feedback 197
d1-18 (Speed Reference
Selection Mode)
Jog Frequency
0 Multi-speed references take priority, and the leveling speed in d1-26 is used for the Jog frequency.
1 Jog frequency cannot be used.
2 Jog frequency cannot be used.