Yaskawa L1000E AC Drive Technical Manual for CIMR-LE Models for Elevator Applications - Manual (Page 393)

B.3 Parameter Table
YASKAWA ELECTRIC SIEP YAIL1E 01A YASKAWA AC Drive L1000E Technical Manual 393
Pa
ra
met
er
L
is
t
B
◆ n: Advanced Performance Set-Up
The n parameters are used to adjust more advanced performance characteristics such as speed feedback detection, Online
Tuning for motor line-to-line resistance, and PM motor control tuning.
■ n1: Hunting Prevention
■ n2: Speed Feedback Detection Control (AFR) Tuning
■ n5: Inertia Compensation
L8-99
(B98H)
Current Monitoring Level Sets the current monitoring level as a percentage of the drive's rated current. Sets the level of
current used to monitor the status of the current (H2-††. = 5C) when the Current Monitoring
Selection (L8-89) is enabled and set to 1.
Default: 10.0 %
Min: 0.0 %
Max: 50.0 %
231
<1> Default setting is determined by the drive model (o2-04).
<3> Setting 3 available in V/f and OLV control only.
<4> Parameter setting value is not reset to the default value when the drive is initialized.
No. (Addr.) Name Description Setting Page
n1-08
(1105H)
Leakage Current Vibration Control
Selection
0: Method 1
1: Method 2
Parameter does not normally require adjustment.
Default: 0
Min: 0
Max: 1 232
No. (Addr.) Name Description Setting Page
n2-01
(584H)
Speed Feedback Detection Control
(AFR) Gain
Sets the internal speed feedback detection control gain in the automatic frequency regulator
(AFR).
If hunting occurs, increase the set value. If response is low, decrease the set value.
Default: 1.00
Min: 0.00
Max: 10.00 232
n2-02
(585H)
Speed Feedback Detection Control
(AFR) Time Constant 1
Sets the time constant used for speed feedback detection control (AFR).
Default: 50 ms
Min: 0 ms
Max: 2000 ms
232
n2-03
(586H)
Speed Feedback Detection Control
(AFR) Time Constant 2
Sets the AFR time constant to be used during regen.
Default: 750 ms
Min: 0 ms
Max: 2000 ms
No. (Addr.) Name Description Setting Page
n5-01
(5B0H)
<4> Default setting value is dependent on the drive model (o2-04).
Inertia Compensation Selection
0: Disabled
1: Enabled
Default: 0
Min: 0
Max: 1 233
n5-02
(5B1H)
Motor Acceleration Time
Sets the time required to accelerate the motor at 100% torque from 0 to the nominal speed.
Default: <4>
Min: 0.001 s
Max: 10.000 s 233
n5-03
(5B2H)
Inertia Compensation Gain
Sets the ratio between motor and load inertia. Lower this setting if overshoot occurs at the end
of acceleration.
Default: 1.00
Min: 0.00
Max: 100.00 234
n5-07
(170H)
Speed Feedback Compensation
Selection
0: Disabled
1: Enabled
2: Test Mode
Default: 1
Min: 0
Max: 2
235
n5-08
(171H)
Speed Feedback Compensation
Gain (P)
Sets the proportional gain for the Speed Feedback Compensation.
Default: 12.00
Min: 0.00
Max: 300.00
235
No. (Addr.) Name Description Setting Page
All Modes
common
_
All Modes
common
_
common
_ CLV CLV/PM V/f OLV
common
_ CLV CLV/PM V/f OLV
common
_ CLV CLV/PM V/f OLV
common
_ CLV CLV/PM V/f OLV
common
_ CLV CLV/PM V/f OLV
common
_ CLV CLV/PM V/f OLV
common
_ CLV CLV/PM V/f OLV
common
_ CLV CLV/PM V/f OLV