Yaskawa L1000E AC Drive Technical Manual for CIMR-LE Models for Elevator Applications - Manual (Page 381)

B.3 Parameter Table
YASKAWA ELECTRIC SIEP YAIL1E 01A YASKAWA AC Drive L1000E Technical Manual 381
Pa
ra
met
er
L
is
t
B
■ F5: Digital Output Card (DO-A3)
■ F6: Communication Option Card
For more details on a specific option card, refer to the instruction manual for the option card.
No.(Addr.) Name Description Setting Page
F5-01
(399H)
Terminal P1-PC Output Selection
Sets the function for contact output terminals M1-M2, M3-M4, and photocoupler output
terminals P1 through P6.
Default: 0
Min: 0
Max: 161
191
F5-02
(39AH)
Terminal P2-PC Output Selection
Default: 1
Min: 0
Max: 161
F5-03
(39BH)
Terminal P3-PC Output Selection
Default: 2
Min: 0
Max: 161
F5-04
(39CH)
Terminal P4-PC Output Selection
Default: 4
Min: 0
Max: 161
F5-05
(39DH)
Terminal P5-PC Output Selection
Default: 6
Min: 0
Max: 161
F5-06
(39EH)
Terminal P6-PC Output Selection
Default: 37
Min: 0
Max: 161
F5-07
(39FH)
Terminal M1-M2 Output Selection
Default: F
Min: 0
Max: 161
F5-08
(3A0H)
Terminal M3-M4 Output Selection
Default: F
Min: 0
Max: 161
F5-09
(3A1H)
DO-A3 Output Mode Selection 0: Output terminals are each assigned separate output functions.
1: Binary code output
2: Use output terminal functions selected by parameters F5-01 through F5-08.
Default: 0
Min: 0
Max: 2 191
No.(Addr.) Name Description Setting Page
F6-01
(3A2H)
Operation Selection after
Communications Error 0: Ramp to stop. Decelerate to stop using the deceleration ramp in C1-02.
1: Coast to stop.
2: Fast Stop. Decelerate to stop using the deceleration ramp in C1-09.
3: Alarm only.
Default: 1
Min: 0
Max: 3 191
F6-02
(3A3H)
External Fault from
Communication Option Detection
Selection
0: Always detected
1: Detection during run only
Default: 0
Min: 0
Max: 1 192
F6-03
(3A4H)
External Fault from
Communication Option Operation
Selection
0: Ramp to stop. Decelerate to stop using the deceleration ramp in C1-02.
1: Coast to stop.
2: Fast Stop. Decelerate to stop using the deceleration ramp in C1-09.
3: Alarm only.
Default: 1
Min: 0
Max: 3 192
F6-04
(3A5H)
bUS Error Detection Time
Sets the delay time for error detection if a bus error occurs.
Default: 2.0 s
Min: 0.0 s
Max: 5.0 s 192
F6-06
(3A7H)
Torque Limit Selection from
Communications Option
0: Disabled. Torque limit from option card disabled.
1: Enabled. Torque limit from option card enabled.
Default: 0
Min: 0
Max: 1 192
F6-08
(36AH)
<1>
Reset Communication Parameter
0: Communication-related parameters (F6-††) are not reset when the drive is initialized using
A1-03.
1: Reset all communication-related parameters (F6-††) when the drive is initialized using
A1-03.
Default: 0
Min: 0
Max: 1 192
F6-35
(3D0H)
CANopen Node ID
Sets the node address.
Default: 0
Min: 0
Max: 126 –
All Modes
common
_
All Modes
common
_
All Modes
common
_
All Modes
common
_
All Modes
common
_
All Modes
common
_
common
_ CLV CLV/PM V/f OLV
All Modes
common
_
All Modes
common
_