Lenze 8400 HighLine - Manual (Page 1571)

Lenze · 8400 HighLine · Referenzhandbuch · DMS 10.0 EN · 06/2014 · TD05/TD14
1571
Index
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Optical location 110
Optimising the response to setpoint changes (SC) 242
Optimising the response to setpoint changes (SLVC) 199
Option "Lock bFail at TroubleQSP" 128
Original application|control source (C00008) 804
oS1: Maximum speed limit reached (error message) 651
oS2: Max. motor speed (error message) 651
Oscillation damping 269
Oscillation damping filter time (C00235) 856
Oscillation damping influence (C00234) 856
Oscilloscope function 671
ot1: Maximum torque reached (error message) 649
ot2: Speed controller output limited (error message) 653
oU: DC bus overvoltage (error message) 649
Output frequency (C00058) 814
Output power (C00980) 1028
Overchange 581
Override 593
Override point of field weakening (C00080) 819
OxI
Current (C00437) 887
OxU
Voltage (C00436) 887
OxU/I
Gain (C00434) 886
Input value (C00439) 888
Offset (C00435) 887
P
Parameter change-over 776
Parameterisable function blocks 1184
Password data (C00505) 907
Password protection 42
PC manual control 88
PDO mapping 704 , 706 , 708 , 710
PDO synchronisation 720
Peak current limitation 151
Phase sequence reversal 272
Plant parameters 137
PLI without motion
Adaptation of ident angle (C02875) 1146
Adaptation of time duration (C02872) 1145
Ident. el. rotor displ. angle (C02873) 1145
Optimisation factor (C02870) 1145
Running time (C02871) 1145
PLI without motion (C02874) 1146
Pole position identification 223
Port block "LP_CanIn1" 704
Port block "LP_CanIn2" 706
Port block "LP_CanIn3" 708
Port block "LP_CanIn4" 710
Port block "LP_CanOut1" 712
Port block "LP_CanOut2" 713
Port block "LP_CanOut3" 714
Port block "LP_CanOut4" 715
PosExecute (control bit) 517
PosExecute control bit 517
Position control 282
Position encoder selection (C00490) 906
Position follower 591
Position teaching 589
Positioning 575
Positioning modes 582
Power section ID (C00093) 822
Power-on time meter (C00179) 847
Pre-defined error field (I-1003) 744
Printing the interconnection 1227
Process data objects, identifiers 716
Processing time 690
Producer heartbeat time (I-1017) 748
Product type code (C00203) 852
Profile data
Acceleration (C01303) 1087
Deceleration (C01304) 1088
Final speed (C01305) 1088
Position (C01301) 1087
Positioning mode (C01300) 1086
Sequence profile (C01307) 1089
Speed (C01302) 1087
S-ramp time (C01306) 1088
TP profile (C01308) 1089
TP signal source (C01309) 1089
Profile entry 579
Profile generator (L_DFRFG) 1335
Profile linkage with velocity changeover (overchange) 581
PS01: No memory module (error message) 659
PS02: Par. set invalid (error message) 659
PS03: Par. set device invalid (error message) 659
PS04: Par. set Mci invalid (error message) 660
PS07: Par. memory module invalid (error message) 660
PS08: Par. device invalid (error message) 660
PS09: Par. format invalid (error message) 660
PS10: Memory module binding invalid (error message) 660
PSM
Activate Lss sat. char. (C02859) 1140
Imax Lss saturation characteristic (C02855) 1140
Lss saturation characteristic (C02853) 1140
Maximum motor current field weakening (C00938) 1020
PTC 299
PW protection config MCI (C00510) 912
PW protection config X1(CAN) (C00509) 911
PW protection config X6(DIAG) (C00508) 910
PW protection internal config (C00506) 908
Q
Quick stop setting (C00104) 824