Lenze 8400 TopLine - Manual (Page 1753)

Lenze · 8400 TopLine · Reference manual · DMS 6.0 EN · 06/2014 · TD05/TD14
1753
Index
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Flying restart function 264
Oscillation damping 272
Selection help 153
Selection of switching frequency 256
Selection of the control type 149
Sensorless vector control (SLVC) 193
Servo control (SC) 226
Slip compensation 271
V/f characteristic control (VFCplus) 157
V/f control (VFCplus + encoder) 186
Motor control (C00006) 883
Motor cosine phi (C00091) 906
Motor current (C00054) 897
Motor data 135
Motor data changeover 859
Motor data parameter list 859
Motor holding brake 655
Motor load monitoring (I2xt) 294
Motor magnetising current (C00095) 906
Motor magnetising inductance (C00092) 906
Motor overcurrent monitoring 296
Motor parameter identification 141
Motor parameter identification is active 116
Motor phase direction of rotation (C00905) 1122
Motor phase error monitoring before operation 301
Motor phase failure monitoring 300
Motor phase failure threshold (C00599) 1019
Motor rotor position (C00060) 898
Motor rotor position (C00927) 1124
Motor rotor resistance (C00082) 904
Motor rotor time constant (C00083) 904
Motor selection 135
Motor speed monitoring 304
Motor stator leakage inductance (C00085) 904
Motor stator resistance (C00084) 904
Motor temp. feedback system (C01193) 1175
Motor temperature (C00063) 899
Motor temperature monitoring (PTC) 297
Motor thermal sensor (C01190) 1174
Motor voltage (C00052) 897
Motorparameter (C00969) 1131
Multilingualism 38
N
Network management telegram (NMT) 762
NMT (network management) 762
Node address 758
Node ID 758
Number of CAN SDO channels (C00366) 962
Number of encoder increments (C00420) 970
O
oC1: Power section - short circuit (error message) 709
oC10: Maximum current reached (error message) 711
oC11: Clamp operation active (error message) 713
oC12: I2xt overload - brake resistor (error message) 713
oC13: Maximum current for Fch exceeded (error message) 714
oC14: Direct-axis current controller limitation (error message)
715
oC15: Cross current controller limitation (error message) 715
oC16: Torque controller limitation (error message) 715
oC17: Clamp sets pulse inhibit (error message) 711
oC2: Power section - earth fault (error message) 710
oC5: Ixt overload (error message) 708
oC6: I2xt overload - motor (error message) 716
oC7 296
oC7: Motor overcurrent (error message) 708
oH1: Heatsink overtemperature (error message) 706
oH12: Motor overtemperature MultiEncoder (error message)
707
oH3: Motor temperature (X106) triggered (error message) 707
oH4: Heatsink temp. > shutdown temp. -5°C (error message)
706
oH6: Motor temperature MultiEncoder >= C121 (error
message) 707
oH7: Motor temperature resolver >= C121 (error message) 706
oH9: Motor overtemperature resolver (error message) 707
Open-circuit monitoring
HTL encoder 370
Open-circuit monitoring (C00498) 1000
Operating conditions (CAN on board) 750
Operating mode
Homing 606
Manual jog 625
Position follower 649
Positioning 633
Speed follower 604
StandBy 567
Stop 648
Operating mode change with profile number 578
Operation with increased rated power 260
Operation with safety module 568
Optical location 112
Optimising the response to setpoint changes (SC) 241
Optimising the response to setpoint changes (SLVC) 203
Option "Lock bFail at TroubleQSP" 130
Original application|control source (C00008) 887
oS1: Maximum speed limit reached (error message) 711
oS2: Max. motor speed (error message) 712
Oscillation damping 272
Oscillation damping filter time (C00235) 941
Oscillation damping influence (C00234) 941
Oscilloscope function 733
ot1: Maximum torque reached (error message) 708
ot2: Speed controller output limited (error message) 714