Rockwell Automation 8520 9/Series CNC Integration Maintenance Manual Documentation Set - Manual (Page 842)

Error and System Messages
Section 16
16-22
Message Description
INVALID PARAMETER VALUE An attempt was made to assign an invalid value (typically too large or too small of a value) to a
paramacro parameter.
INVALID POCKET NUMBER An attempt was made to enter a tool pocket number that exceeds the allowable number of tool
pockets in the random tool table. This error occurs when a P-word that is too large or too small
is programmed in a G10.1L20 block.
INVALID POCKET PROFILE An invalid pocket profile was programmed in a lathe roughing or finishing cycle.
INVALID POSITION FB TYPE System was incorrectly AMPed with a Yaskawa type encoder (absolute or incremental) on the
position feedback device when separate position and velocity feedback devices are used.
INVALID PROGRAM NUMBER (P) A program number called by a sub-program or paramacro call is invalid. A P-word that calls a
sub-program or paramacro can only be an all-numeric program name as many as 5 digits long.
The O-word preceding the numeric program number in control memory cannot be entered with
the P-word.
INVALID REMOTE NODE NAME An error occurred in G05 DH+ communications block.
INVALID REMOTE STATION TYPE An error occurred in G05 DH+ communications block.
INVALID REPEAT COUNT (L) An L parameter that programs the number of times a paramacro or other operation is to be
repeated was programmed incorrectly or out of the legal range. The L-word for repeat count
must be a whole, positive number. Decimal values and negative values are invalid. The
maximum value of an L-word is 9999.
INVALID ROUGHING CYCLE (P/Q) WORD VALUE When executing a roughing cycle, the starting or ending sequence number of the contour
defining blocks cannot be found in the currently executing program. The sequence number of
the contour blocks is programmed using the P and Q words. These blocks can be anywhere in
the program provided they are resident in the same program, sub-program, or paramacro
program that contains the calling block.
INVALID SCALE FACTOR (P-WORD) An invalid scale factor has been specified. The P-word has a range of 0.0001 to 999.99999.
INVALID SERVO HARDWARE TYPE The AMP servo parameter that selects the servo type does not match the hardware found on
the control when the AMP file is downloaded. Either AMP is misconfigured or the servo
hardware installed on your system is not correctly installed or not of the correct type.
INVALID SHAFT POCKET When entering a custom tool in the random tool table, an attempt was made to assign a shaft
pocket position that is not in the range of the number of pockets assigned to the tool. The shaft
pocket number must be equal to or less than the number assigned for the number of pockets.
INVALID SHAFT POCKET VALUE A program is attempting to enter a custom tool in the random tool table with a invalid shaft
pocket position (not in the range of the number of pockets assigned to the tool). The shaft
pocket number must be equal to or less than the number assigned for the number of pockets.
The shaft pocket value is assigned in a G10.1 block following the R-word.
INVALID SPCMD VALUE A invalid special command error typically occurs when the servo PROMs are not compatible
with the main processor PROMs. Check the software version numbers and contact
Allen-Bradley customer support services.
INVALID SYMBOL NAME An error occurred in G05 DH+ communications block.
INVALID T-CODE FORMAT This is an invalid T-Code Format
INVALID_THREAD_ANGLE An attempt was made to program an angle that is outside the allowable range, which is 0
through 120 degrees.
INVALID THRESHOLD RATE An invalid threshold percentage was entered for a tool group while setting tool management
data. The threshold percentage must range between 0 and 100 percent. Only whole positive
numbers can be entered. If using a G10 block, the threshold percentage is entered with a
Q-word.
INVALID TIME FORMAT MUST BE HH:MM:SS An invalid time format was entered. The time format must be hour / minute / second
(HH/MM/SS).
INVALID TOOL AXIS This is an invalid Tool Axis.