Rockwell Automation 8520 9/Series CNC Integration Maintenance Manual Documentation Set - Manual (Page 846)

Error and System Messages
Section 16
16-26
Message Description
MEMORY CRASH - REFORMAT A major error has occurred within the system RAM memory. All part programs stored in memory
will have to be be deleted by performing a reformat operation. This will not remove the current
versions of AMP or PAL from the system.
MEMORY FULL There is no more RAM memory space for part program storage. If you are in the process of
editing a part program, your changes cannot be saved.
MIDSTART NOT ALLOWED FROM TAPE You cannot perform a mid-program start on a program that is stored on tape. The program must
first be transferred to RAM memory.
MINIMUM RPM LIMIT AUXILIARY SPINDLE 2 The commanded aux spindle 2 speed requested by the control is less than the AMPed minimum
aux spindle 2 speed for the current gear being used. This requires a gear change operation or a
change in the programmed aux spindle 2 speed. In some cases, the <SPINDLE SPEED
OVERRIDE> switch may be sufficient.
MINIMUM RPM LIMIT AUXILIARY SPINDLE 3 The commanded aux spindle 3 speed requested by the control is less than the AMPed minimum
aux spindle 3 speed for the current gear being used. This requires a gear change operation or a
change in the programmed aux spindle 3 speed. In some cases, the <SPINDLE SPEED
OVERRIDE> switch may be sufficient.
MINIMUM RPM LIMIT FIRST SPINDLE The commanded spindle 1 speed requested by the control is less than the AMPed minimum
spindle 1 speed for the current gear being used. This requires a gear change operation or a
change in the programmed spindle 1 speed. In some cases, the <SPINDLE SPEED
OVERRIDE> switch may be sufficient.
MINIMUM RPM LIMIT PRIMARY SPINDLE The commanded primary spindle speed requested by the control is less than the AMPed
minimum primary spindle speed for the current gear being used. This requires a gear change
operation or a change in the programmed primary spindle speed. In some cases, the
<SPINDLE SPEED OVERRIDE> switch may be sufficient.
MINIMUM RPM LIMIT SECOND SPINDLE The commanded spindle 2 speed requested by the control is less than the AMPed minimum
spindle 2 speed for the current gear being used. This requires a gear change operation or a
change in the programmed spindle 2 speed. In some cases, the <SPINDLE SPEED
OVERRIDE> switch may be sufficient.
MINIMUM RPM LIMIT THIRD SPINDLE The commanded spindle 3 speed requested by the control is less than the AMPed minimum
spindle 3 speed for the current gear being used. This requires a gear change operation or a
change in the programmed spindle 3 speed. In some cases, the <SPINDLE SPEED
OVERRIDE> switch may be sufficient.
MIRROR NOT ALLOWED ON ROLLOVER AXIS You cannot perform mirrored motion using an axis with rollover.
MISSING 1394 I/O RING ADDR This message indicates that a 1394 amplifier ID has been AMPed but not defined in I/O ring
assignment from ODS. The 1394 amplifier must be a defined device on the 9/Series fiber optic
I/O ring.
MISSING ( [ ) AFTER FUNCTION NAME Paramacro and calculator functions must have their values enclosed in [ ], for example, SIN[5].
MISSING ( ] ) Paramacro and calculator functions must have their values enclosed in [ ], for example, SIN[5].
The control has found that a right bracket “]”is missing in the current operation.
MISSING (END) COMMAND The control has found an end-of-program block (M02 or M30) before it has read the END
command for a paramacro DO loop.
MISSING (F) IN INVERSE TIME An F-word must be programmed in every motion block that is not rapid when in inverse time
feed mode (G93). F is not modal in G93.
MISSING (GOTO) COMMAND An IF paramacro condition does not have a GOTO with a sequence number following the
condition.
MISSING A (DO) COMMAND A WHILE paramacro condition does not have a DO with a loop identifier following the condition.
MISSING ADAPTIVE FEED DATA An attempt was made to create a transfer line part program from the quick view screen with
incomplete adaptive feedrate data.
MISSING COMMA An error occurred in G05 DH+ communications block.
MISSING COMMA OR RIGHT PARENTHESIS An error occurred in G05 DH+ communications block.