Lenze 8400 - Manual (Page 598)

9 Diagnostics & error management
9.10 Error messages of the operating system
598
Lenze · 8400 protec HighLine · Reference manual · DMS 3.0 EN · 03/2013 · TD05
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Sd11: Speed limit for feedback system 67 [xx.0123.00201]
Sd3: Open circuit - feedback system [xx.0123.00205]
An01: AIN1_I < 4 mA [xx.0125.00001]
An02: AIN2_I < 4 mA [xx.0125.00002]
Io11: DigOut level [xx.0125.00011]
Response (Lenze setting printed in bold) Setting: C00607 ( Adjustable response)
 0: No Reaction  1: Fault  2: Trouble  3: TroubleQuickStop  4: WarningLocked  5: Warning  6: Information
Cause Remedy
Maximally permissible speed of the feedback system
connected to DI6/DI7 reached.
Reduce speed of the rotation shaft/feedback system.
n
encoder
<= (f
max
x 60) / encoder increment
(for f
max
= 10 kHz)
Response (Lenze setting printed in bold) Setting: C00586 ( Adjustable response)
 0: No Reaction  1: Fault  2: Trouble  3: TroubleQuickStop  4: WarningLocked  5: Warning  6: Information
Cause Remedy
• HTL encoder cable interrupted.
• HTL encoder is defective.
Note: May also be caused by a very dynamic acceleration
or starting up against a blocked motor shaft (e.g. with a
closed holding brake).
• Check HTL encoder cable.
• Check HTL encoder.
• Check related terminals.
• Switch off monitoring ( C00586 = "0: No reaction")
when the HTL encoder is not used.
Response (Lenze setting printed in bold) Setting: C00598/1 ( Adjustable response)
 0: No Reaction  1: Fault  2: Trouble  3: TroubleQuickStop  4: WarningLocked  5: Warning  6: Information
Cause Remedy
Open-circuit monitoring for analog input 1 has tripped.
• Only if the analog input has been configured as a
current loop of 4 ... 20 mA ( C00034/1 = 2).
• Check wiring of the analog X3/A1I input terminal for
open circuit.
• Check minimum current values of the signal sources.
Response (Lenze setting printed in bold) Setting: C00598/2 ( Adjustable response)
 0: No Reaction  1: Fault  2: Trouble  3: TroubleQuickStop  4: WarningLocked  5: Warning  6: Information
Cause Remedy
Open-circuit monitoring for analog input 2 has tripped.
• Only if the analog input has been configured as a
current loop of 4 ... 20 mA ( C00034/2 = 2).
• Check wiring of the analog X3/A2I input terminal for
open circuit.
• Check minimum current values of the signal sources.
Response (Lenze setting printed in bold) Setting: C00598/3 ( Adjustable response)
 0: No Reaction  1: Fault  2: Trouble  3: TroubleQuickStop  4: WarningLocked  5: Warning  6: Information
Cause Remedy
The actual level of a digital output does not correspond
to the setpoint level.
• Check wiring of the digital output terminal for short
circuit to earth.
• Check whether the digital output terminal is by
mistake triggered externally with a HIGH signal
although a LOW signal should be output.