Rockwell Automation 8520-ARM2 9/Series CNC AMP Reference Manual Documentation Set - Manual (Page 745)

9/Series CNC AMP Reference Manual
Index
I--iii
Corner Override, 23-8
Creating
Document File, 2-34
New AMP File, 2-5
CSS (On/Off), 19-12
CSS Parameters, 11-2
CSS Radius During G00 Rapid, 11-5
Current as a % of RMS, Peak, (Digital), 7-77
Current Integral Gain, (Digital), 7-98
Current Proportional Gain, (Digital), 7-97
Cutter Compensation
Basic Setup, 23-2
Corner Override
Angle, 23-9
Distance From Corner (DFC), 23-9, 23-11
Distance To Corner (DTC), 23-9, 23-10
Percentage (%), 23-12
Defining Offsets, (Mill Only), 23-4
Error Detection, 23-13
Generated Blocks, 23-5
Interference Detection, 23-13
M Word Interference Detection
Disable, 23-15
Enable, 23-16
Maximum Number of Non-Motion Blocks, 23-8
Minimum Feed Reduction %, 23-6
Overview, 23-1
Reverse Compensated Motion Detection, 23-14
Type A, Type B, 23-2
Cycle Clearance Amount, 25-6
Cycles
Clerance Amount, 25-6
Fine Boring Shift Direction, 25-5
Fine Boring Shift in Q-word, 25-4
Fixed Drilling Axis, 25-9
Ignore Dwell in Tapping Cycles, 25-7
Parameters, 25-3
Rapid to Drilling Hole, 25-8
Retract Amount for Peck Drilling, 25-3
Threading Pullout Distance, 25-10
Cylindrical Feed Axis Name, 30-2
Cylindrical Interpolation
cylindrical feed axis name, 30-2
cylindrical linear axis name, 30-4
cylindrical park axis name, 30-3
cylindrical rotary axis name, 30-5
feed axis park location, 30-13
rotary center feed coordinate, 30-6
rotary center park coordinate, 30-7
Cylindrical Linear Axis Name, 30-4
Cylindrical Park Axis Name, 30-3
Cylindrical Rotary Axis Name, 30-5
D
D: Integer Format, 17-3, 32-13
D: Word Format, 17-4
DAC Voltage and Spindle Gear Parameters, 12-3, 13-3,
14-3
Dead Band, adaptive depth, 32-11
Default CSS Axis Name, 11-3
Default Orient Angle, 12-16, 13-16, 14-16
Default Orient Direction, 12-15, 13-15, 14-15
Default Position Offset, 15-7
Deleting, Axis, 3-8
Depth Probe, 32-1
(analog servo card), 7-27
Depth Sensor Dead Band, 32-11
Depth Sensor Travel Limit, 32-12
Deskew Gain, 36-11
Deskew Master Servo Name, 36-6
Deskew Parameters for Split Axes, 36-1
Deskew Slave Servo Name, 36-9
Detecting a Hardstop, 7-82
DH+ Pass Through, enabling, 2-32
DH+ pass thru Enable, see adapter block transfer, 33-6
Diameter Axis __ (cylindrical grinders), 4-11
Diameter Axis Name (lathes), 4-10
Digital Servo Parameters, 7-87
Servo Feedback, 7-3
Digital Spindle Drive, 7-100
Direction of Probe Trip, 32-10
Direction to Move Off Limit Switch, 5-10
Distance Coded Marker, Machine Position at DCM Scale 0,
5-23
Distance Coded Markers
Automatic Homing (G28), 5-16
Homing Linear Scales, 5-8
Manual Homing, 5-8