Lenze E82xVxxxKxxxxx - Manual (Page 353)

Function library
Free interconnection of digital signals
Free configuration of digital outputs
10
l
353 EDS82EV903 EN 3.0
Switching conditions
Selection in C0415/x Relay/digital output (not inverted)
1 Parameter set 2 or parameter set 4 is active
(DCTRL1−PAR−B0) Increases/HIGH if parameter set 2 or 4 is
active
2 Pulse inhibit active (DCTRL1−IMP) Increases/HIGH in case of s, controller
inhibit (CINH), overvoltage or undervoltage
3 I
max
limit reached (MCTRL1−IMAX)
(C0014 = −5−: torque setpoint reached)
Increases/HIGH if motor current = C0022 or
motor current = C0023
4 Frequency setpoint reached (DCTRL1−RFG1=NOUT) Increases/HIGH if output frequency =
frequency setpoint
5 Ramp function generator 1: input = output
(NSET1−RFG1−I=O) Increases/HIGH if the condition is complied
with
6 Values have fallen below frequency threshold Q
min
(f < C0017) (PCTRL1−QMIN)
Increases/HIGH if the output frequency >
C0017 (based on setpoint)
7 Output frequency = 0 (DCTRL1−NOUT=0) Increases/HIGH because
l Frequency setpoint = 0 Hz, t
if
has expired
l DC injection brake (DCB) active
l Controller inhibited (CINH)
8 Controller inhibit active (DCTRL1−CINH) Increases/HIGH if the controller is inhibited
due to
l X3/28 = LOW
l C0410/10 = active
l s
13 Group signal (DCTRL1−OH−PTC−LP1−FAN1−WARN)
Overtemperature (
J
max
− 5 °C) (DCTRL1−OH−WARN)
or motor overtemperature (DCTRL1−LP1−PTC−WARN)
or motor phase failure (DCTRL1−LP1−WARN) or fan
failure (only active with 8200 motec)
Increases/HIGH if one of the messages is
active
14 DC bus overvoltage (DCTRL1−OV) Increases/HIGH if the permissible voltage
threshold is reached
15 CCW rotation (DCTRL1−CCW) Increases/HIGH in case of CCW rotation
16 Ready for operation (DCTRL1−RDY) Increases/HIGH if the controller is ready for
operation
Decreases/LOW in case of
l TRIP error message
l Undervoltage or overvoltage
17 Parameter set 3 or parameter set 4 active
(DCTRL1−PAR−B1) Increases/HIGH if parameter set 3 or 4 is
active
18 Values have fallen below TRIP or Q
min
or pulse
inhibit (IMP) is active (DCTRL1−TRIP−QMIN−IMP)
Decreases/LOW if at least one of the three
conditions (selection 25, 6 or 2) is complied
with
19 PTC warning (DCTRL1−PTC−WARN) Decreases/LOW if thermal contact or PTC
reports motor overtemperature
20 Apparent motor current < current threshold
(DCTRL1−IMOT<ILIM) Increases/HIGH if the condition is complied
with
21 Apparent motor current < current threshold and
output frequency > Frequency threshold Q
min
(DCTRL1−(IMOT<ILIM)−QMIN)
22 Apparent motor current < current threshold and
ramp function generator 1: input = output
(DCTRL1−(IMOT<ILIM)−RFG−I=0)
23 Motor phase failure warning (DCTRL1−LP1−WARN)
24 Min. output frequency reached (f £ C0010)
(PCTRL1−NMIN)
Increases/HIGH if output frequency >
C0010
25 TRIP error message (DCTRL1−TRIP) Increases/HIGH in case of TRIP error
message
26 Motor is running (DCTRL1−RUN) Increases/HIGH if output frequency ¹ 0 Hz
27 Motor is running / CW rotation (DCTRL1−RUN−CW) Increases/HIGH if output frequency > 0 Hz