Lenze E82xVxxxKxxxxx - Manual (Page 544)

Index 17
l
544 EDS82EV903 EN 3.0
Operating modes, for standard
applications, 204 , 256
Operating status, display, 453
Operating threshold
− auto DCB, 289 , 292 , 387
− Qmin, 387
Operation, at earth−leakage circuit
breaker, 101
operation, noise optimised, 270
Operation of mid−frequency motors,
507
Operation on public supply systems,
EN 61000−3−2, 100
Optimisation of the controller and
mains load, 103
Oscillation damping, 272
− Reduction of speed oscillations, 272
Output data, 31
Output signal − analog outputs, range,
336 , 429
Output signals
− Analog, Configuration, 332
− Digital, Configuration, 348
Outputs
− Analog, 332
− Digital, 348
P
Parameter
− altering and saving by means of
keypad E82ZBC, 228
− Copy using the E82ZBC keypad, 229
− Copy using the XT EMZ9371BC
keypad, 240
Parameter set changeover
− AC motor braking, 294
− Controlled deceleration after mains
failure, 278
Parameter set management, 215 ,
368 , 380
− own basic setting, 216 , 369 , 381
Parameter set transfer, 215 , 216 ,
368 , 369 , 380 , 381
Parameter sets
− changeover, 372
− Management, 368
Parameter setting, 222
− Code, 222
− Via bus system, 223
− Via operating module (keypad), 222
− Via PC, 223
− with E82ZBC keypad, 205 , 224
− With XT EMZ9371BC keypad, 209 ,
235
Parameters
− Change and store using the XT
EMZ9371BC keypad, 239
− saving non−volatilely, 217 , 370 ,
382
− transferring with keypad, 215 , 216 ,
368 , 369 , 380 , 381
Password
− Delete, 232 , 243
− Enter
Keypad E82ZBC, 231
Keypad XT EMZ9371BC, 242
Password protection, 390
− Activate
Keypad E82ZBC, 231
Keypad XT EMZ9371BC, 242
− Call a protected function, Keypad
E82ZBC, 232
− Deactivate
Keypad E82ZBC, 232
Keypad XT EMZ9371BC, 243
− Keypad XT EMZ9371BC, 242
PM synchronous motors, 19
Pollution, 28 , 191 , 197
Power control, 515
Power terminals
− Brake resistor connection, 129 , 139
− Mains connection, 123 , 124 , 133 ,
134 , 143 , 151 , 159
− Motor connection, 129 , 139 , 146 ,
154 , 162
− Relay connection, 130 , 140 , 147 ,
155 , 163
− Specification, 114
Power−on time, 366 , 400
Pressure control, Dry running
protection, 502
Process controller, 318
− "Debouncing" of digital output
signal PCTRL1−LIM, 402
− "Debouncing" of digital output
signal PCTRL1−SET=ACT , 402
− Activate inverted control, 403
− Actual value selection, 324
− Control properties, 318
− Deceleration PCTRL1−LIM=HIGH, 402
− Deceleration PCTRL1−SET=ACT, 402
− Differential threshold
PCTRL1−SET=ACT, 403
− Fade−in time, 402
− Fade−in/fade−out, 403
− Fade−out time, 402
− Invert output, 403
− Lower limit for output, 402
− Offset for inverse characteristic, 402
− Root function for actual value, 403
− Setpoint
Acceleration time, 402
Deceleration time, 402
− Setpoint feedforward control, 322
− Setpoint selection, 322
− Upper limit for output, 402
Process data output words, Free
configuration, 354
Process variable, Calibration of
application I/O, 364 , 432
Product description, 18
− Application as directed, 19
Protection against unexpected
start−up, 492
− operating mode, 493
− safety relay, 495
Protection of persons, 23
− with earth−leakage circuit breaker,
101
Protective insulation of circuits, 488
PTC motor monitoring, 359
Q
Quick stop, 289