Lenze E82xVxxxKxxxxx - Manual (Page 545)

Index 17
l
545 EDS82EV903 EN 3.0
R
Range of setpoint selection
− application I/O, 219 , 298 , 388
− standard I/O, 219 , 298 , 388
Rated data, 488
− Brake chopper EMB9352, 487
− Brake chopper, internal, 484
− Brake module EMB9351, 487
− for 400 V mains voltage, 37 , 55
− for 500 V mains voltage, 44 , 60
− For a mains voltage of 230 V, 32 , 52
− Operation with increased rated
power, 51
− Operation with rated power, 32
Rating, Brake resistors, 491
Reaction times of digital inputs, 343
Reduce noise emissions, 104
Relay connection
− 0.25 ... 11 kW, 130 , 140
− 15 ... 90 kW, 147 , 155 , 163
Relay output, Configuration, 348
reluctance motors, 19
Remote parameterisation
− Using the E82ZBC keypad, 233
− Using the XT EMZ9371BC keypad,
244
Reset time, Imax controller, 265 , 327
, 390
Resetting, fault message, 459
Residual hazards, 23
Running optimisation, 268
S
S−shaped ramps, Smooth
acceleration/deceleration, 286
Safe standstill, 492
Safe torque off, 492
− functional test, 499 , 501
− operating mode, 493
− safety relay, 495
Safety, safety engineering, 492
Safety engineering, 492
Safety function
− functional test, 499 , 501
− Safe torque off, 492
Safety instructions, 20
− Application as directed, 19
− definition, 17
− layout, 17
Safety relay, 495
Saving parameter sets, , 368
Selection of direction of rotation, 24
Setpoint changeover, 313
Setpoint selection, 296 , 394
− Bipolar, 301
− Inverse, 302
− Process controller, 322
− range, 219 , 298 , 388
− Scaled, 396
− Selection, 394
− unipolar, 301
− via bus systems, 312
− via fixed setpoint (JOG), 309
− via motor potentiometer, 307
− with keypad, 311
Setpoint source, Select, 296
Setpoint source selection, 296
Setpoint summation, 514
Setting range, 218 , 282 , 386
Signal flow diagram
− Controller state (STAT1, STAT2), 533
− Controller with application I/O, 519
− Controller with Application I/O and
communication module, 520
− Controller with communication
module, 521
− Controller with fieldbus function
module, 522
− Controller with fieldbus function
module and communication module,
523
− Controller with standard I/O, 517
− Controller with Standard I/O and
communication module, 518
− Controller with system bus function
module, 524
− Controller with system bus function
module and communication module,
525
− Device control (DCTRL1), 532
− Fieldbus function module (FIF−IN,
FIF−OUT), 537
− Motor control (MCTRL1), 530
− Motor control (MCTRL1) with
Application I/O, 531
− Process controller and setpoint
processing (PCTRL1), 528
− Process controller and setpoint
processing (PCTRL1) with Application
I/O, 529
− Speed setpoint conditioning (NSET1),
526
− Speed setpoint conditioning (NSET1)
with Application I/O, 527
− System bus (CAN−Objekt 1,
CAN−Objekt 2), 535
Signal selection
− Analog, 298
Jumper position, 298
− Digital, 303
Site altitude, 28 , 487
Skip frequency, 273
Slip compensation, 268
Smooth acceleration/deceleration,
286
Software version, 366 , 391
Special motors, Operation of, 272
Speed control, 508
Speed oscillations, 272
Standard I/O
− Description, 190
− range of setpoint selection, 219 ,
298 , 388
Standard I/O PT, Terminal
assignment, 171 , 178 , 188
Start options, 275
Status display
− Keypad E82ZBC, 226
− keypad XT EMZ9371BC, 237
Status word, 398
Stopping, 286
Supply conditions, 124 , 127 , 135 ,
137 , 144 , 145 , 152 , 153 , 160 ,
161 , 467 , 470
Supply forms / electrical supply
conditions, 99
Switching frequency of inverter, 270
− noise optimised, 270
Switching on the motor side, 24