Lenze E94AxHE Servo Drives 9400 HighLine (Firmware 01-37) - Manual (Page 674)

9400 HighLine | Parameter setting & configuration
Index
674 Firmware 1.37 - 09/2006
L
MCTRL_dnMotorFreqAct (C784) 601
MCTRL_dnMotorPosAct (C770) 599
MCTRL_dnMotorPosRefValue (C812) 605
MCTRL_dnMotorSpeedAct (C772) 599
MCTRL_dnOutputPosCtrlMotor_s (C792) 603
MCTRL_dnOutputSpeedCtrl (C775) 600
MCTRL_dnPosCtrlAdapt (C811) 604
MCTRL_dnPosCtrlOutLimit (C808) 604
MCTRL_dnPosSet (C800) 603
MCTRL_dnSpeedAdd (C802) 603
MCTRL_dnSpeedCtrlAdapt (C810) 604
MCTRL_dnSpeedCtrlIntegrator (C815) 605
MCTRL_dnSpeedLowLimit (C805) 603
MCTRL_dnSpeedSet_s (C817) 605
MCTRL_dnTorqueAct (C774) 600
MCTRL_dnTorqueAdd (C803) 603
MCTRL_dnTorqueCtrlAdapt (C809) 604
MCTRL_dnTorqueHighLimit (C807) 604
MCTRL_dnTorqueLowLimit (C806) 604
MCTRL_dwMaxDeviceCurrent (C789) 602
MCTRL_dwMaxEffMotorTorque (C788) 602
MCTRL_dwMaxMotorSpeed (C781) 601
MCTRL_dwMaxMotorTorque (C782) 601
MCTRL_dwMotorVoltageAct (C783) 601
Memory module
File system has been formatted 477
File system has been restored 477
File system is faulty 454
Memory module has been changed 453
Memory module has been removed 450
Memory module is defective or missing 450 , 451
Memory module is missing 449
Messages motor interface (C2560) 622
Min. S-ramp time (C2706) 639
Modulation modes 80
Moment of inertia (C273) 566
Monitoring 439
Motor
Actual current value > C00620 472
Actual speed value > C00596 473
Calculated electromotive force factor unrealistic 470
Calculated flux factor unrealistic 470
Calculated leakage inductance unrealistic 472
Calculated motor impedance unrealistic 468
Calculated mutual inductance unrealistic 469
Calculated rotor resistance unrealistic 469
Calculated rotor time constant unrealistic 470
Device current is too low for rated magnetisation 469
Overtemperature 463
Phase resistance is too high 469
PTC has triggered 466
Rated current 469
Temperature > C00121 463
Temperature sensor defective 465
Motor - cosine phi (C91) 553
Motor - magnetising current (C92) 553
Motor - mutual inductance (C79) 552
Motor - pole pair number (C59) 549
Motor - rated current (C88) 553
Motor - rated frequency (C89) 553
Motor - rated speed (C87) 553
Motor - rated voltage (C90) 553
Motor - rotor resistance (C82) 552
Motor - rotor time constant (C83) 552
Motor brake
Angular drift with closed brake is too large 533
Automatically activated when the waiting time has
elapsed 533
Status monitoring error 533
Motor control
Task overflow 471
Motor control selection (C6) 547
Motor current (C54) 548
Motor data are inconsistent 469 , 471
Motor encoder 112
Module selected under C00495 not available 473
Motor encoder (C495) 586
Motor interface 64
% signals (C2568) 622
Dig. signals (C2569) 623
Motor load I²xt > C00120 467
Motor load I²xt > C00127 467
Motor mounting direction (C2527) 616
Motor operating temperature (C1194) 609
Motor overload protection (I²xt) (C120) 555
Motor parameter identification cancelled 476
Motor pos. contr. output (C2557) 621
Motor reference speed (C11) 547
Motor standstill time constant (C494) 586
Motor stator leakage inductance (C85) 552
Motor stator resistance (C84) 552
Motor temp. warning threshold (C121) 555
Motor temperature
Module selected under C01193 not available 473
Motor temperature (C63) 550
Motor thermal sensor (C1190) 608
Motor voltage (C52) 548
MXI1
CAN module is missing or incompatible 495
Digital frequency module is missing or incompatible
494
Ethernet module is missing or incompatible 494
ICM module missing or incompatible 494
Module changed during operation 450
Module has been changed 453
Module is defective or missing 451
Module is missing or incompatible 493
PROFIBUS module is missing or incompatible 493
Wrong module 452
MXI2