Intel CONTROLLERS 413808 - Manual (Page 157)

Intel ® 413808 and 413812 I/O Controllers in TPER Mode
October 2007 Developer’s Manual
Order Number: 317805-001US 157
Address Translation Unit (PCI-X)—Intel
®
413808 and 413812
2.14.15 Inbound ATU Base Address Register 1 - IABAR1
The Inbound ATU Base Address Register 1 (IABAR1) together with the Inbound ATU
Upper Base Address Register 1 (IAUBAR1) defines the block of memory addresses
where the inbound translation window 1 begins. The inbound ATU decodes and
forwards the bus request to the 4138xx internal bus with a translated address to map
into 4138xx local memory. The IABAR1 and IAUBAR1 define the base address and
describes the required memory block size; see Section 2.14.23, “Determining Block
Sizes for Base Address Registers” on page 164 . Bits 31 through 12 of the IABAR1 is
either read/write bits or read only with a value of 0 depending on the value located
within the IALR1. This configuration allows the IABAR1 to be programmed per PCI Local
Bus Specification, Revision 2.3.
The programmed value within the base address register must comply with the PCI
programming requirements for address alignment. Refer to the PCI Local Bus
Specification, Revision 2.3 for additional information on programming base address
registers.
Warning:
When IALR1 is cleared prior to host configuration, the user should also clear the
Prefetchable Indicator and the Type Indicator. Assuming IALR1 is not cleared:
c. Since non prefetchable memory windows can never be placed above the 4 Gbyte address boundary,
when the Prefetchable Indicator is cleared prior to host configuration, the user should also set the
Type Indicator for 32 bit addressability.
d. For compliance to the PCI-X Protocol Addendum to the PCI Local Bus Specification, Revision 2.0,
when the Prefetchable Indicator is set prior to host configuration, the user should also set the Type
Indicator for 64 bit addressability. This is the default for IABAR1.
Table 41. Inbound ATU Base Address Register 1 - IABAR1
Bit Default Description
31:12 00000H Translation Base Address 1 - These bits define the actual location of window 1 on the PCI bus.
11:04 00H Reserved.
03 0
2
Prefetchable Indicator - When set, defines the memory space as prefetchable.
02:01 00
2
Type Indicator - Defines the width of the addressability for this memory window:
00 - Memory Window is locatable anywhere in 32 bit address space
10 - Memory Window is locatable anywhere in 64 bit address space
00 0
2
Memory Space Indicator - This bit field describes memory or I/O space base address. The ATU does not
occupy I/O space, thus this bit must be zero.
PCI
IOP
Attributes
Attributes
28 24 20 16 12 8 4 0 31
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rw
rv
rv
rv
rv
rv
rv
rv
rv
rv
rv
rv
rv
rv
rv
rv
rv
rw
ro
rw
ro
ro
ro
ro
ro
Attribute Legend:
RV = Reserved
PR = Preserved
RS = Read/Set
RW = Read/Write
RC = Read Clear
RO = Read Only
NA = Not Accessible
Register Offset
+018H